Confidential
1-4
Error
codes
Problem
Refer
to:
Error
codes
Problem
Refer
to:
85 Tray 1 (T1) is not installed into the
machine.
1-23 B3 Detection error of the scanning area on
the left end
1-29
86 Tray 2 (T2) is not installed into the
machine.
1-23 B4 Detection error of the scanning area on
the right end
1-29
B5 Detection error of horizontal scanning
edge reduction in scanning area setting
1-2987 Toner cartridge whose color is used
reaches the end of life when
implementing calibration from the
control panel.
1-20
88 Paper jam inside the machine 1-22
B6 Detection error of horizontal scanning
edge magnification in scanning area
setting
1-29
89 Incorrect paper size in duplex printing 1-23
8A Paper jam in Tray 1 (T1) 1-24
B9 Scanning light adjustment error is
detected.
1-30
8B Paper jam in Tray 2 (LT) 1-24 BB White level data error 1-30
8C Paper jam in MP tray (MP) 1-24 BD Black level data error 1-30
BE Detection error of scanning starting edge 1-308E Auto color registration failure when
implementing it from the control panel
1-25
BF Duplex scanning cannot be implemented
due to too long document.
1-31
8F Sensor sensitivity adjustment failure
when implementing auto color
registration from the control panel
1-25
C0 Identification failure for a new toner
cartridge (K)
1-31
99 Specified paper size is not supported
for duplex printing (DX).
1-7 C1 Identification failure for a new toner
cartridge (Y)
1-31
9B Request on developing bias voltage
adjustment
1-7 C2 Identification failure for a new toner
cartridge (M)
1-31
9C Request on auto color registration 1-7 C3 Identification failure for a new toner
cartridge (C)
1-31
C4 Tray 2 (LT) plate-up function malfunction 1-32
9D Incorrect sensor measurement value
when implementing auto color
registration from the control panel
1-25
C5 EL lamp electrifying failure 1-32
C6 Toner cartridge mis-dividing 1-32
C7 Insufficient DIMM memory 1-7
C8 RAM area for secure data full 1-33
9E Toner cartridge whose color is used
reaches the end of life when
implementing auto color registration
from the control panel.
1-20
C9 Defective DIMM is installed. 1-7
A1 Front cover opened 1-26 CA Excess current to USB device 1-33
A2 Document is too long. 1-26 CB Belt unit is not installed into the machine. 1-33
A3 Document rear sensor is not turned on
when feeding the document.
1-26 CC Fuser unit is not installed into the
machine.
1-34
A5 Fax scanning error
(The first warning only)
1-27 CD Drum unit is not installed into the
machine.
1-34
CE Waste toner box is not installed into
the machine.
1-36A6 Fax scanning error (The second
warning that the same error with A5
occurs again)
1-27
CF Waste toner box full 1-36
A7 Color parameter failure 1-27 D0-DF Modem error 1-36
AD DMA transfer error 1-27 E0 Program error. (An error occurred in
the ROM checksum.)
1-37
AE FB unit home position sensor is not
turned on.
1-28
E1 Program error. 1-37
E6 NVRAM error on main PCB 1-37AF FB unit home position sensor is not
turned off.
1-28
EB NVRAM reading error on laser unit 1-37
EF Incorrect print coverage value 1-38B0 Harness for scanning is not connected
correctly.
1-28
F8 Battery connection failure 1-38
To Next Page
Loading...
