BYD PMW20 - Page 50

PMW20
99
PMW20
98
Fig.1.2
SM-PMW202020001-EN
SM-PMW202020001-EN
PARAMETER CHANGE
PARAMETER NAME PARAMETER DESCRIPTION MENU
ACCELER. DELAY
ACCELERATION DELAY IS SHOWN AS
ACCELERATION RATE. THE LOWER THE VALUE,
THE SHORTER THE ACCELERATION TIME.
PARAMETER CHANGE
RELEASE BRAKING HANDLE ACCELERATOR RELEASES BRAKING RATE. PARAMETER CHANGE
TILLER BRAKING
RESPONSE TIME OF INTERLOCKING AND
CLOSING THE HANDLE
PARAMETER CHANGE
UPRIGHT BRAKING UNUSED, HIGH SPEED LIMIT BRAKING PARAMETER CHANGE
INVERS. BRAKING RESPONSE TIME OF BRAKING IN INVERSION PARAMETER CHANGE
DECEL. BRAKING REDUCTION RATE OF THE MOTOR PARAMETER CHANGE
PEDAL BRAKING PEDAL BRAKING, UNUSED PARAMETER CHANGE
SPEED LIMIT BRK.
INSTRUMENT FAULT, SWITCH TO THE REDUCTION
RATE WITH A SLOW SPEED (GENERALLY SHOWN
AS BALANCING WEIGHT), UNUSED.
PARAMETER CHANGE
EPS STEER BRAK. BRAKING WHEN STEERING FAULT APPEARS PARAMETER CHANGE
MAX SPEED FORW
MAXIMUM FORWARD SPEED
PARAMETER CHANGE
MAX SPEED BACK
MAXIMUM BACKWARD SPEED
PARAMETER CHANGE
HYD SPEED FINE
ADJUST PROPORTIONAL VALVE (COARSE TUNING)
SO THAT PUMP MOTOR WORKS NORMAL AT AN
APPROPRIATE SPEED.
PARAMETER CHANGE
HYDRO COMPENS.
ADJUST PROPORTIONAL VALVE (FINE TUNING) SO
THAT PUMP MOTOR WORKS NORMAL AT AN
APPROPRIATE SPEED
PARAMETER CHANGE
CUTBACK SPEED
LOW-SPEED MODE PERFORMED BY
LOW-SPEED KEY ON THE HANDLE
PARAMETER CHANGE
H&S CUTBACK SPEED OF UPRIGHT WALKING MODE PARAMETER CHANGE
THMOT AL. CUTB.
IF MOTOR TEMPERATURE IS LOWER THAN THE SET
PERCENT, THE SPEED THEREOF WILL REDUCE
PARAMETER CHANGE
BDI AL. CUTBACK
IF MOTOR POWER IS LOWER THAN THE SET
PERCENT, THE SPEED THEREOF WILL REDUCE.
PARAMETER CHANGE
STEER CTB.1
IT IS REDUCTION RATE OF ANGLE SET BY STEER
CTB ANGL1
PARAMETER CHANGE
STEER CTB.2
IT IS REDUCTION RATE OF ANGLE SET BY STEER
CTB ANGL2
PARAMETER CHANGE
STEER CTB.3
IT IS REDUCTION RATE OF ANGLE SET BY STEER
CTB ANGL3
PARAMETER CHANGE
STEER CTB ANGL 1 SEGMENTATION SETTING OF STEERING ANGLE 1
STEER CTB ANGL 2 SEGMENTATION SETTING OF STEERING ANGLE 2
STEER CTB ANGL 3 SEGMENTATION SETTING OF STEERING ANGLE 3
TURTLE H&S TIME
PRESS THE TIME KEY AND ENTER THE UPRIGHT
WALKING MODE.
PARAMETER CHANGE
RETURN TIME
TIME ON CANCELING OPERATION AUTOMATICALLY
UNDER THE UPRIGHT WALKING MODE
PARAMETER CHANGE
TURTLE TIME DISP UPRIGHT WALKING MODE PARAMETER CHANGE
FREQUENCY CREEP
THE SPEED OF THE MOTOR WHEN THERE IS NO
ANALOG QUANTITY FORWARD OR BACKWARD.
PARAMETER CHANGE
MAXIMUM CURRENT OUTPUT RATE OF CONTROLLER CURRENT PARAMETER CHANGE
ACC SMOOTH ACCELERATION CURVE PARAMETER CHANGE
INV SMOOTH ACCELERATION CURVE WHEN MOTOR REVERSES. PARAMETER CHANGE
STOP SMOOTH
THE FREQUENCY AT THE END OF THE SMOOTH
EFFECT OF ACCELERATION PARABOLA.
PARAMETER CHANGE
BRK SMOOTH
DECELERATION CURVE
PARAMETER CHANGE
PUMP IMAX
THE CURRENT (SPEED) LEVEL OF
THE PUMP MOTOR
PARAMETER CHANGE
PU. DECELER. DEL
DECELERATION DELAY OF THE PUMP
MOTOR (EFFECTIVE PUMP CONTROL)
PARAMETER CHANGE
MAX SPEED LIFT
MAXIMUM LIFT SPEED (LEVEL SET BY
CURRENT PUMP CURRENT)
PARAMETER CHANGE
PUMP CREEP SPEED PARAMETER CHANGE
PUMP COMPENSAT. PARAMETER CHANGE
MIN EVP MINIMUM CURRENT OFFERED TO LOWERING VALVE PARAMETER CHANGE
MAX EVP MAXIMUM CURRENT OFFERED TO LOWERING VALVE PARAMETER CHANGE
PU. ACCELER. DEL
ACCELERATION DELAY OF THE PUMP
MOTOR (PUMP CONTROL IS EFFECTIVE)
PARAMETER CHANGE
HYDRO TIME
THE DURATION OF THE PUMP MOTOR AFTER
RELEASING HYDRAULIC PRESSURE
PARAMETER CHANGE
AUXILIARY TIME
AUXILIARY TIME（AN ELECTRIC BRAKING FORM
AND A FUNCTION OF BALANCING WEIGHT）
PARAMETER CHANGE
STOP BRK SMOOTH
THE FREQUENCY AT THE END OF THE SMOOTH
EFFECT OF DECELERATION PARABOLA.
PARAMETER CHANGE