EasyManuals Logo

Cisco Catalyst 4500 Series Installation Guide

Cisco Catalyst 4500 Series
194 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #46 background imageLoading...
Page #46 background image
Chapter 1 Product Overview
Supervisor Engines
1-28
Catalyst 4500 Series Switches Installation Guide
78-14409-08
When two Supervisor Engine Vs are present in a Catalyst 4507R and Catalyst
4510R, all four uplinks are active on both Primary (active) and Secondary
(standby) supervisor engines by default, or two uplinks will be active in a
nonredundant configuration. This limits access to slot 10 on the Catalyst 4510R
to ports 3 and 4 only. You can only use the 2-port Gigabit Ethernet switching
module (WS-X4302-GB) or the Access Gateway Module (WS-X4604-GWY) in
slot 10 (flex-slot), when a Supervisor Engine V is used.
10-Gigabit Ethernet Uplink Ports
The 10-Gigabit Ethernet uplink ports operate in full-duplex mode only, and are
only on the WS-X4516-10GE and WS-X4013+10GE. These ports use the
hot-swappable 10GBASE X2 optical transceivers. The X2s have SC connectors
to interface with multimode fiber (MMF) and single-mode fiber (SMF) cable.
On a Catalyst 4510R with a Supervisor Engine V-10GE, the user has the option
to use either four Gigabit Ethernet uplinks using SFPs or two 10-Gigabit Ethernet
uplinks using X2s. The user also has the option of using the Gigabit Ethernet and
10-Gigabit Ethernet uplinks simultaneously. With this option, the tenth slot can
only support the WS-X4302-GB switching module. On a Catalyst 4507R, the user
can use the Gigabit Ethernet uplinks and 10-Gigabit Ethernet uplinks
simultaneously.
When two Supervisor Engine V-10GEs are present in a Catalyst 4510R or
Catalyst 4507R switch, or two Supervisor Engine II-Plus 10GEs are present in a
Catalyst 4507R, one X2 uplink is active on both the primary (active) and
secondary (standby) supervisor engines by default, or two uplinks will be active
in a nonredundant configuration.
SFP Ports
Gigabit Ethernet SFP ports operate in full-duplex mode only and are present on
the WS-X4013+TS, WS-X4516-10GE and WS-X4013+10GE supervisors, as
well as some switching modules. These ports use the 1000BASE-SX,
1000BASE-LX, Cisco Coarse Wave Division Multiplexing (CWDM ) SFPs,
1000BASE-T SFP, and 1000BASE-ZX SFP. SFP connectors vary with interface
type and may use multimode fiber (MMF), single-mode fiber (SMF) cable, or
copper Ethernet cables.

Table of Contents

Other manuals for Cisco Catalyst 4500 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 4500 Series and is the answer not in the manual?

Cisco Catalyst 4500 Series Specifications

General IconGeneral
SeriesCatalyst 4500 Series
CategorySwitch
Layer SupportLayer 2, Layer 3
Form FactorModular chassis
StackableNo
Chassis Slots3, 6, 7, 10
Power Supply OptionsAC, DC
RedundancyPower supply, Supervisor engine
Network ManagementCisco IOS Software CLI, SNMP, Cisco Prime Infrastructure
FeaturesSecurity, QoS
Port DensityUp to 384 ports per chassis
Security Features802.1X, ACLs, DHCP Snooping, Dynamic ARP Inspection, IP Source Guard
Supervisor Engine8-E

Related product manuals