D-Link xStack DES-3200 Series User Manual

xStack® DES-3200 Series Layer 2 Ethernet Managed Switch CLI Reference Manual
16
8
19
IGMP SNOOPING COMMANDS
The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table:
Command Parameters
config igmp_snooping [vlan_name <vlan_name 32> | vlanid <vidlist> | all] {state [enable | disable] |
fast_leave [enable | disable]} (1)
config igmp_snooping querier [vlan_name <vlan_name 32> | vlanid <vidlist> | all] {query_interval <sec 1-
65535> | max_response_time <sec 1-25> | robustness_variable <value 1-
255> | last_member_query_interval <sec 1-25> | state [enable | disable] |
version <value 1-3>} (1)
config router_ports [<vlan_name 32> | vlanid <vidlist>] [add | delete] <portlist>
config router_ports_forbidden [<vlan_name 32> | vlanid <vidlist>] [add | delete] <portlist>
enable igmp_snooping {forward_mcrouter_only}
show igmp_snooping {vlan <vlan_name 32> } | vlanid <vidlist>}
disable igmp_snooping {forward_mcrouter_only}
show router_ports {[vlan <vlan_name 32> | vlanid <vidlist>]} {[static | dynamic | forbidden]}
show igmp_snooping group {[vlan <vlan_name 32> | vlanid <vidlist>]} {data_driven}
config igmp_snooping
data_driven_learning
[vlan_name <vlan_name 32> | vlanid <vidlist> | all] {aged_out [enable |
disable]} (1)
config igmp_snooping
data_driven_learning
max_learned_entry
<value 1-1024>
clear igmp_snooping data_
driven _group
[all | [vlan_name <vlan_name 32> | vlanid <vlanid> ] [<ipaddr>] | all]
show igmp_snooping host {[vlan <vlan_name 32> | vlanid <vidlist> | ports <portlist> | group <ipaddr>] }
config igmp
access_authentication ports
[<portlist> | all] state [enable | disable]
show igmp
access_authentication ports
[all | <portlist>]
Each command is listed, in detail, in the following sections:
config igmp_snooping
Used to co
nfigure IGMP snooping on the Switch.
Purpose
config igm
p_snooping [vlan_name <vlan_name 32> | vlanid <vidlist> | all] {state
[enable | disable] | fast_leave [enable | disable]} (1)
Syntax
This
command is used to configure IGMP snooping on the Switch.
Description
Parameters
<vlan_name 32>  The name of the VLAN for which IGMP snooping is to be
configured.
<vidlist>  Specifies a list of VLANs to be configured.
all – Specifies that all VLANs configured on the Switch will be configured.

D-Link xStack DES-3200 Series Specifications

General

Managed	Yes
Layer	Layer 2
MAC Address Table Size	8K
Quality of Service (QoS)	802.1p
Security Features	ACL, 802.1X, Port Security
Jumbo Frame Support	Up to 9KB
Dimensions	Varies by model
Weight	Varies by model
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
Standards Compliance	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x, IEEE 802.1D, IEEE 802.1w, IEEE 802.1s, IEEE 802.1Q, IEEE 802.1p
Forwarding Rate	13.1 Mpps (48-port)