Danfoss VLT AutomationDrive User Manual

H
Hand On..................................................................................... 25, 29, 46
Harmonics.................................................................................................. 6
I
IEC 61800-3............................................................................................. 14
Induced Voltage.................................................................................... 12
Initialisation............................................................................................ 30
Input
Current................................................................................................. 14
Disconnect.......................................................................................... 14
Power............................................................ 12, 14, 22, 49, 60, 6, 21
Signal.................................................................................................... 31
Signals........................................................................................... 16, 17
Terminals................................................................. 10, 14, 17, 21, 52
Voltage................................................................................... 23, 49, 53
Installation.............................................. 5, 8, 9, 12, 16, 20, 22, 54, 23
Isolated Mains........................................................................................ 14
L
Leakage
Current.......................................................................................... 21, 12
Current (>3,5mA)............................................................................. 13
Lifting.......................................................................................................... 9
Local
Control................................................................................... 27, 29, 46
Control Panel..................................................................................... 27
Mode..................................................................................................... 25
Operation............................................................................................ 27
Start....................................................................................................... 25
Local-control Test................................................................................. 25
M
Main Menu................................................................................ 28, 31, 28
Mains
Mains.................................................................................................... 12
Supply............................................................................. 62, 66, 67, 68
Supply (L1, L2, L3)............................................................................ 71
Voltage..................................................................... 28, 29, 46, 52, 56
Manual Initialisation............................................................................ 30
Mechanical Brake Control................................................................. 20
Menu
Keys................................................................................................ 27, 28
Structure....................................................................................... 29, 35
Modbus RTU........................................................................................... 20
Motor
Cables....................................................................................... 8, 12, 13
Current....................................................................... 6, 24, 53, 56, 28
Data............................................................. 24, 25, 30, 54, 53, 56, 24
Leads..................................................................................................... 54
Output.................................................................................................. 71
Power..................................................................................... 10, 12, 56
Protection.................................................................................... 12, 75
Rotation........................................................................................ 25, 28
Speeds.................................................................................................. 23
Status...................................................................................................... 6
Wiring............................................................................................ 12, 13
Wiring, And......................................................................................... 22
Mounting............................................................................................ 9, 22
Multiple
Frequency Converters............................................................. 12, 13
Motors.................................................................................................. 21
N
Navigation Keys......................................................... 23, 31, 46, 27, 29
Noise Isolation................................................................................ 12, 22
O
Open Loop....................................................................................... 17, 31
Operation Keys...................................................................................... 29
Optional Equipment......................................................... 14, 17, 23, 6
Output
Current.......................................................................................... 47, 53
Performance (U, V, W)..................................................................... 71
Signal.................................................................................................... 35
Terminals...................................................................................... 10, 21
Overcurrent............................................................................................ 47
Overload Protection........................................................................ 8, 12
Overvoltage..................................................................................... 26, 47
P
PELV.................................................................................................... 14, 44
Power
Connections....................................................................................... 12
Factor........................................................................................ 6, 13, 22
Power-dependent................................................................................ 62
Pre-start.................................................................................................... 21
Programming
Programming......... 5, 17, 26, 28, 30, 33, 35, 40, 52, 23, 27, 29,
31
Example............................................................................................... 31
Protection And Features.................................................................... 75
Pulse/Encoder Inputs.......................................................................... 72
Q
Quick
Menu....................................................................................... 31, 33, 28
Set-up................................................................................................... 24
Index
VLT
®
AutomationDrive Operating
Instructions
86 MG.33.AJ.02 - VLT
®
is a registered Danfoss trademark

Danfoss VLT AutomationDrive Specifications

General

Supply Voltage	3 x 200-240 V ±10% 3 x 380-500 V ±10% 3 x 525-600 V ±10%
Enclosure	IP20
Output Power Range	0.25 kW - 1.5 MW
Communication Protocols	Modbus RTU
Protection Features	Overcurrent, Overvoltage, Undervoltage, Short circuit, Ground fault, Motor overload
Ambient Temperature Range	-10°C to +50°C (14°F to 122°F)