Datalogic Smart-VS

To Next Page

To Previous Page

INSTALLATION

29 SMART-VS PLUS

MOUNTING AND POSITIONING SMART-VS PLUS

Using the Smart-VS Plus mounting brackets you can obtain rotation on the various axes

of the device as shown in the diagram below:

Figure 13 - Positioning with Mounting Bracket

Main Page

Table of Contents3
Preface6
About this Manual6
Manual Conventions6
Technical Support6
Support through the Website6
Warranty7
Compliance8
General8
Power Supply8
EMC Compliance8
European Declaration of Conformity8
UKCA Declaration of Conformity8
FCC Compliance9
EAC Compliance9
LED Safety9
Handling10
General View12
Rapid Configuration14
Connect the System14
Mount and Position the Device15
HMI Button Configuration16
Button Teaching Procedure16
Button Incremental Teaching Procedure (Optional)17
Button Re-Teaching Procedure (Optional)18
Firmware Rollback and Reset Configurations (Optional)19
Using the Smart-VS Webapp20
Dashboard Page21
Current Bank22
IP Settings22
Settings Backup22
Device Information23
Global Settings23
Hamburger Icon23
Teaching24
Step 1: Image Setup24
Trigger Settings24
Step 2: Acquire GOOD25
Step 3: Acquire no GOOD26
Step 4: Learn27
Step 5: Response Time28
Monitoring29
Upper Bar29
Main Area30
Bottom Bar30
Download the Filmstrip31
I/O Settings32
Introduction33
Product Description33
Excellent Performance34
Ease of Setup34
Ease of Use34
Flexible Solution34
Industrial Strength34
Indicator and Keypad Button35
Aiming System36
LED Spots36
Model Selection and Order Information37
Internal Lighting System37
Accessories37
Application Examples38
Installation39
Package Contents39
Mechanical Dimensions40
Mounting and Positioning Smart-VS Plus42
Electrical Connections43
Power Supply44
Inputs44
Trigger and External Push-Button Connection45
Outputs45
Digital I/O Diagram45
Data Valid Timing Details46
On-Board Ethernet Interface47
Typical Layouts48
Sensor-Like Setup48
Webapp for Initial Configuration and Occasional Monitoring49
Setup with Telnet Communication for Job Switching50
Reading Features51
FOV Calculation51
Detection Diagram52
Multi Job Configuration53
Job Switching Via Smart-VS Webapp53
Job Switching Via Telnet Communication54
Maintenance55
Cleaning55
Troubleshooting56
Technical Features58
Tcp/Ip Communication60
Connection60
Protocol Overview61
Description of Available Features61
Use of Synchronous Features61
Use of Asynchronous Features62
Delimiters and Separator63
Device Control Commands64
Command Format64
Reply Format64
List of Available Device Control Functions65
Return Codes66
Bankstatus66
CRTJB (Createjob)67
MDFJB (Modifyjob)67
EXTJB (Exitjob)68
TRNJB (Trainjob)68
CNGJB (Changejob)68
BNKST (Bankstatus)69
GTRJB (Getrunningjob)69
GTDVCS (Getdevicestatus)69
ACQIMG (Acquireimage)70
CLRBNK (Clearbank)70
CLRJBS (Clearjobs)70
GTATS (Getasynctaskstatus)71
FNZJB (Finalizejob)71
FNZTRN (Finalizetraining)72
Example of Creating a New Job72
Example of Incremental Training72
Binary File Upload and Download Commands73
Upload Command Format73
Upload Reply Format73
Download Command Format73
Download Reply Format74
Device Procedure Control Commands75
Procedure Control Command Format and Return Codes75
List of Available Procedure Control Functions75
CRTJBF (Createjobfile)76
CRTBCK (Createbackup)76
ULBF (Uploadbinaryfile)76
DLBF (Downloadbinaryfile)77
STJBF (Storejobfile)77
STBCK (Storebackup)78
FNZJBF (Finalazejobfile)78
FNZBCK (Finalazebackup)79
FNZJST (Finalizejobstorage)79
FNZBST (Finalizebackupstorage)79
Example Upload of a Binary File80
Scenario 180
Scenario 281
Example Downloading a Binary File82
Scenario 182
Scenario 283
Protocol Exceptions83

Table of Contents

Related product manuals