Dormakaba ED900 - Installation Instructions Manual

124 pages

Save Page as PDF

To Next Page

ED900

Low Energy Swing Door Operator

(Fine cover)

Double egress doors

Installation Instructions

08125330 – 02-2020

| EN |

Main Page

Default Chapter2
- Table of Contents2
- ED900 Arm Configurations4
- Product Description 55
- Handing of Door5
- Double Egress Door Installation Configurations6
Safety Information7
ED900 Product Overview8
- ED900 Push Arm System8
- ED900 Pull Arm System8
- ED900 - Double Egress Door Configurations9
- ED900 Operator Component Views10
ED900 Hardware - Double Door12
- ED900 Operator and Mounting Plate12
- Door Decal Kit, Low Energy12
- Double Door Communication Cable12
- Arm Assemblies13
- Axle Extension Sleeves and Extensions13
- ED900 Mounting Plate Screw Kit14
- ED900 Arm Mounting Screw Kits14
- ED900 Standard Cover Kit14
- ED900 Full Width Cover, Mounting Plate Extension, and Cables - Option15
- Key Switch Panels - Option16
- Push Arm Door Stop - Option16
- Conduit Box and Wiring Kit - Options17
Technical Data18
- ED900 Technical Data18
- Operating Specifications19
Operational Mode Overview19
- ED900 Door Closer Modes19
- Low Energy Product19
User Interface20
- Overview20
- Button Keypad and Display20
- Program and Exit Only Switches21
- Operator Status Leds21
System Accessories22
- System Accessory Electrical Connections22
- ED900 Terminal Board Interfaces23
ED900 Door Signage24
- Low Energy Operator24
- Door Signage, Low Energy Double Egress Swing Door25
- Safety Information Label, Low Energy Swing Doors26
11 Recommended Tools and Torque Chart27
- Recommended Tools27
- Standard Tightening Torque27
- Drill Bits27
12 ED900 Installation Overview28
- Installation Preparation28
- 12.2 ED900 Operator Installation with Standard Covers30
- ED900 Operator Installation with Full30
- ED900 Operators - Assign Active Door and 8 Inactive Door Type30
- ED900 Operators - 115 Vac Customer31
- ED900 Operators - Program Switch31
- Interconnecting Cables31
- Wiring31
13 ED900 Installation Templates32
- Installation Templates - Pull Arm32
- Installation Templates - Pull as Push35
- Installation Templates - Push Arm36
- Installation Templates, Double Doors38
14 ED900 Operator and Mounting Plate42
Preparation42
- Remove Mounting Plate from each ED90042
- Operator44
- Options - Customer 115 Vac Connection to Terminal Blocks44
- Full Width Cover Option46
- ED900 Operator Preparation and 19 Mounting Plate Assembly46
15 ED900 Mounting Plate and Operator48
Installation48
- 15.1 ED900 Mounting Plate Attachment to48
- Install ED900 Mounting Plate to Jamb And/Or Wall49
- Full Width Cover Option - Install Cables between Mounting Plates50
- Mounting Plate50
  - Connect Customer 115 Vac to ED900 Mounting Plate Terminal Block52
  - Route Accessory Wiring to Active Door Mounting Plate53
- Remove Protective Film Strips from each ED900 Operator54
- Install each ED900 Operator Onto Its54
- Mounting Plate54
- Full Width Cover Option - Install Program Switch, Active Door ED90055
- Full Width Cover Option - 115 Vac Pair Power Cable Connections56
  - Push Arm Installation Templates57
- Arm with Track Mount Installation60
  - Arm with Track Installation60
  - Splined Arm and Track Assemblies60
  - Splined Arm and Track Hardware60
  - Install Hardware into Track61
  - Slide Shoe Assembly61
  - Fasten Track Assembly to Door62
  - Arm Assembly63
  - Arm Assembly with CPD Lever63
    - Fasten Arm to ED900 Operator64
- Measure Door Width, Reveal Depth66
  - Door Width Parameter Tb66
  - Record Door Width Measurement, Tb Value66
  - Tb Parameter Values66
  - Measure and Record Reveal Depth67
  - Rd Parameter Values67
  - Reveal Depth Parameter Rd67
- Operator Spring Tension68
  - Set ED900 Operator Spring Tension68
- Braking Circuit Plug69
  - Braking Circuit Plug Position69
- Power Fail Closing Speed70
  - Set Power Fail Closing Speed70
    - Parameters71
  - First Commissioning74
- Single Door First Commissioning74
  - Set Configuration Parameters75
  - Set Parameter PS, Program Switch Type76
  - Perform Learning Cycle77
- Double Door First Commissioning78
  - Separately Commission Active and Inactive Doors78
  - Set Operator Parameters for Double Door Operation78
  - Connect Communication Cable between Operators80
- Connect Accessory Wiring and Test81
  - Install Accessory Wiring81
  - Test All Accessories81
- Set Track Bumper Stop82
  - Set Track Bumper Stop Position82
- Install Push Arm Door Stop83
  - Install Push Arm Door Stop (Optional Assembly)83
- 28 Install ED900 Cover, End Caps and 57 Spindle Caps84
  - Install Cover and End Caps84
  - Install Spindle Caps85
  - Full Width Cover Option - Install Cover and End Caps86
- 29 Install Door Signage87
- 30 ANSI/BHMA Standards88
  - A156.19 Low Energy Power Operated Doors88
- 31 Upgrade Cards90
  - Container Module90
  - Installing Upgrade Cards91
- Maintenance92
  - Safety Label, Low Energy Swing Doors92
  - ED900 Environment and Cleaning93
  - Yellow LED, Service Level93
  - Pull Arm Maintenance94
  - Arm Fasteners - Torque Requirements95
  - Push Arm Maintenance96
  - ED900 Brake Maintenance97
Appendix A - Driving Parameters - Detail99
- Driving Parameters Detail99
Appendix B - Troubleshooting108
- Red LED Status Codes109
- Troubleshooting Chart, "Ln" Codes110
- Troubleshooting Chart, "E" Codes111
Appendix C - Dormakaba Handheld113
- Dormakaba Handheld Terminal113
- Dormakaba Handheld; Configuration Parameters114
- Dormakaba Handheld; Driving Parameters115
- Dormakaba Handheld; Special Functions116
  - (Upgrade Cards) ED900116
- Dormakaba Handheld; Diagnostics117
- New Dormakaba Handheld; Language119
- Dormakaba Handheld; Firmware Update120
Appendix D - Wiring Diagrams122
- D1.1 Key Switch Panel with RJ45 Connector122
- D2.1 Key Switch Panel123

Dormakaba ED900 - Installation Instructions Manual

Table of Contents

Other manuals for Dormakaba ED900

Related product manuals