19
Code
Panic Restore A1 to 9A
Partial Closing Code C1
Partition Open BA
Partition Close CA
Periodic Test 1C
Periodic UL Test 1C
Police Restore A1 to 9A
Police Alarm A1 to 9A
Quick Arm Closing Code CA
RS-232 Trouble A1 to 9A
RS-232 Restoral A1 to 9A
System Aux Supply Trouble Alarm A1 to 9A
System Bell Trouble Restoral F1
System TLM Line 2 Restoral EE
System Battery Trouble Alarm E1
System AC Trouble Alarm E1
System Battery Trouble Restoral E1
System AC Trouble Restoral E1
System Aux Supply Trouble Restoral A1 to 9A
System Bell Trouble Alarm F1
System TLM Line 1 Restoral EE
System TLM Line 1 Trouble EE
SYSTEM AREA
COMMUNICATOR
MAIN ITEMS
Code
System TLM Line 2 Trouble EE
System Test 1C
System FTC Restoral EE
Technical Alarm A1 to 9A
Technical Restore A1 to 9A
Waterflow Alarm Trouble Restore A1 to 9A
Waterflow Alarm A1 to 9A
Waterflow Alarm Restore A1 to 9A
Waterflow Alarm Trouble A1 to 9A
Automation Restore A1 to 9A
Automation Fault A1 to 9A
Zone Sensor Fault Restore A1 to 9A
Zone Low Battery E1
Zone Sensor Fault A1 to 9A
Zone Fault 1 to 128 A1 to 9A
Zone Fault Restore 1 to 128 A1 to 9A
Zone Low Battery Restore E1
Zone Alarms 1 to 128 A1 to 9A
Zone Trb./Tamp Restoral 1 to 128 A1 to 9A
Zone Restoral 1 to 128 A1 to 9A
Zone Trb./Tamp 1 to 128 A1 to 9A
Fire Alarms
1A QFIREQ - FIRE ALARM - #
11 QFIREQ - SMOKE DETECTOR - #
12 QFIREQ - COMBUSTION - #
13 QFIREQ - WATER FLOW - #
14 QFIREQ - HEAT SENSOR - #
15 QFIREQ - PULL STATION - #
16 QFIREQ - DUCT STATION - #
17 QFIREQ - FLAME SENSOR - #
Panic Alarms
2A QPANICQ - PANIC - #
21 QPANICQ - DURESS - #
22 QPANICQ - SILENT PANIC - #
23 QPANICQ - AUDIBLE PANIC - #
Code Message as seen on receiver
Burglar Alarms
3A QBURGQ - BURGLARY - #
31 QBURGQ - PERIMETER - #
32 QBURGQ - INTERIOR - #
33 QBURGQ - 24 HOUR - #
34 QBURGQ - ENTRY/EXIT - #
35 QBURGQ - DAY/NIGHT - #
36 QBURGQ - OUTDOOR - #
37 QBURGQ - TAMPER - #
General Alarms
4A QALARMQ - GENERAL ALARM - #
44 QALARMQ - SENSOR TAMPER - #
Contact ID
The System ID code and 4 Customer ID codes must be 4 decimal digits. The reporting codes must
be 2 digits and programmed as follows.
Note: Do not program the Opening After Alarm, Buffer Nearly Full, Installer Lead In and
Installer Lead Out reporting codes.
Do not use this format with 1300 Hz I.D.
Zone Alarms and Restorals can be programmed to send different messages to the monitoring
station. For example, if the Reporting code for zone 5 is programmed with ‘34’, the monitoring
station will receive the message ‘QBURGQ
- ENTRY/EXIT - 5’, where 5 is the number of the zone
which has been activated. Different messages to be sent to the monitoring station are:
Code Message as seen on receiver
To Next Page
Loading...
