Eizo ColorEdge CS230 User Manual

42
Chapter6Troubleshooting
6-2. Imaging problems
Problem Possible cause and remedy
1. The screen is too bright or too dark. • Use“Brightness”intheAdjustmentmenutoadjustit.(The
LCDmonitorbacklighthasalimitedlifespan.)Whenthe
screenbecomesdarkorbeginstoicker,contactyour
localEIZOrepresentative.
2. Characters are blurred. • CheckwhetherthePCisconguredtomeettheresolution
andverticalscanfrequencyrequirementsofthemonitor
(see“2-1.CompatibleResolutions”(page15)).
• Use“OutlineEnhancer”intheAdjustmentmenutoadjust
it(see“Toenhanceoutlineofimage”(page21)).
3. Afterimages appear. • AfterimagesareparticulartoLCDmonitors.Avoid
displayingthesameimageforalongtime.
• Usethescreensaverorpowersavingfunctiontoavoid
displayingthesameimageforextendedperiodsoftime.
4. Green/red/blue/white dots or defective
dots remain on the screen.
• ThisisduetoLCDpanelcharacteristicsandisnota
failure.
5. Interference patterns or pressure marks
remain on the screen.
• Leavethemonitorwithawhiteorblackscreen.The
symptommaydisappear.
6. Noise appears on the screen. • IntheAdjustmentmenu,set“Overdrive”to“Off”(see“2-7.
ConguringMovingImagePerformance”(page30)).
• WhenenteringthesignalsofHDCP,thenormalimages
maynotbedisplayedimmediately.
7. (DisplayPort input)
Display position of the windows changes.
• Whenthesignalisswitched,thepositionofthewindow
maybechanged.IntheAdjustmentmenu,set“DPPower
Save”to“Off”(see“5-6.SettingDisplayPortPowerSave”
(page40)).
8. Displays are abnormal. • Use“Screen”-"ColorSpace"(fortheHDMIinput)under
theAdjustmentmenutoadjustit.
9. An image does not display on the entire
screen.
• Thescreenissettoasizeotherthan“Full”.Changethe
settingto“Full”.
• ForCX240,1080iand1080parethemaximumresolutions
whentheHDMIsignalisinput,soanimagecannotbe
displayedusingtheentirescreen.

Eizo ColorEdge CS230 Specifications

General

3D	No
Pixel pitch	0.2652 x 0.2652 mm
Aspect ratio	16:9
Product type	PC monitor
Response time	10.5 ms
Display diagonal	23 \
Display technology	LED
Vertical scan range	47.5 - 61 Hz
Horizontal scan range	26 - 68 kHz
Viewable size diagonal	584 mm
Viewable size, vertical	286.4 mm
Contrast ratio (dynamic)	-
Contrast ratio (typical)	1000:1
Display number of colors	1.073 billion colors
Viewable size, horizontal	509.2 mm
Display brightness (typical)	300 cd/m²
Supported graphics resolutions	1920 x 1080 (HD 1080)
HDCP	Yes
USB hub version	2.0
VGA (D-Sub) ports quantity	0
USB Type-A downstream ports quantity	4
Pivot angle	0 - 90 °
Tilt angle range	0 - 30 °
Number of OSD languages	9
Panel mounting interface	100 x 100 mm
On Screen Display (OSD) languages	CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, ITA, JPN, SWE
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	54 W
Power consumption (standby)	0.5 W
Power consumption (typical)	21 W
Certification	CUDO, TCO 6.0, TUV/S, TUV/Ergonomics, TUV/GS, cTUVus, CE, c-Tick, CB, VCCI-B, FCC-B, ICES-003-B, RoHS, WEEE, GOST-R
Product color	Black
Market positioning	Graphics design
Cables included	AC, DVI, USB
Operating temperature (T-T)	0 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Harmonized System (HS) code	85285210

Weight and Dimensions

Depth (with stand)	245.5 mm
Height (with stand)	526.5 mm
Weight (with stand)	7500 g
Depth (without stand)	75 mm
Width (without stand)	544 mm
Height (without stand)	353 mm
Weight (without stand)	4800 g