Erratic results ...................................................... 35
exceptionally high noise...................................... 48
Explanations of the safety instructions ................. 7
F
Faults .................................................................. 12
Faulty oxygen regulator ...................................... 16
Flow sensor replacement.................................. 110
Flow sensor(3-14) ............................................. 110
Flow stops during analysis.................................. 68
Fluctuating gas flow ............................................ 13
Fluctuating gas flow fault reasons ...................... 14
Front panel ......................................................... 45
Front CS-2000 .................................................... 63
Front of CS-2000 ................................................ 54
Front side ............................................................ 91
Front side view .................................................. 118
Fumes in the resistance furnace ........................ 61
Furnace cleaning mechanism ........................... 126
Furnace pneumatics - additional safety features
(optional) ....................................................... 116
Furnace power failure ....................................... 116
Furnace regulation board TH 43/TH 44 .............. 97
Furnace temperature problem ............................ 60
G
Gas flow controller .............................................. 70
Gas flow controller adjustment and jumper
settings ............................................................ 70
Gas flow diagrams ............................................ 144
Gas flow regulation ....................................... 72, 74
Gas pump ......................................................... 111
Gas pump replacement .................................... 111
Gas pump/ Attenuator ......................................... 57
Gas saving also for resistance furnace ............ 115
Gas saving for resistance furnace operation ... 115,
116
Gas saving mode .............................................. 114
Gas-flow diagram - furnace closed ..................... 35
Golden IR-Path ................................................... 99
Golden path ...................................................... 130
Ground connection of the tube’s cathode is
interrupted ....................................................... 25
H
Halogen trap - installing .................................... 117
Halogen trap installation ................................... 117
Heating elements ................................................ 29
HF 42 .................................................................. 94
HF41 board ....................................................... 114
jumper setting - gas saving mode ............. 114
HF42 ................................................................... 20
HF-42 ................................................................. 18
HF42 board ...................................................... 114
jumper setting - gas saving mode ................ 114
Hi C .................................................................... 80
Hi S .................................................................... 80
High carbon results are erratic ........................... 36
High frequency generator (1-4-4 + 1-4-5S) ....... 33
Higher sensitivity (gain)...................................... 85
I
Induction furnace ............................................. 124
Induction generator control ................................ 94
Infrared base line adjustments ........................... 75
Infrared cell ...................................................... 129
Infrared cell modification - general information .. 75
Infrared cell temperature regulation ................... 84
Infrared electronics .......................................... 100
Infrared source replacement ............................ 101
Inorganic materials (Metals) ............................ 153
Inputs ................................................................. 12
Inputs and Averages Window ............................ 12
Instability reasons .............................................. 47
Integration delay ................................................ 19
IR cell temperature control ................................. 84
IR signal
does not come down to the base line at the end
of analysis ................................................... 66
IR source voltage setting ................................... 83
IR sources in their housing .............................. 102
IR -temperature .................................................. 39
IRC 1.3 ............................................................... 77
IRC 1.4 ............................................................. 100
IRC1.x ................................................................ 80
IRC-1.x ............................................................... 48
IR-cell board IRC1.x sections assignment ......... 80
IR-Cell general test points ................................. 78
IR-cell temperature control is out of range......... 39
IR-current supply, new version ........................ 142
IR-current supply, old version .......................... 141
IR-paths, cleaning and replacing ....................... 99
J
J2 ....................................................................... 94
Jumper position for continuous flow .................. 18
Jumper position for gas saving mode ................ 18
jumper setting .................................................. 114
Jumper settings .................................................. 71
Jumper settings HF 42 ....................................... 94
L
Latch-up effect ................................................... 43
To Next Page
Loading...
Need help?
General
