NS 5.14 Firmware
Index–4 4900002262 rev. A 3-23-21
Val 1 Concentration 2–32, 2–33
Val 2 Concentration 2–32
, 2–33
Val Auto DumpSpectrm 2–33
Val Interval 2–34
, 2–44
Val Perm Constant Kp 2–34
Val Perm Rate Rp 2–34
Val Start Time 2–21
, 2–35, 2–44
Validation Allowance 2–32
,
2–33
Validation DI 2–44
Validation Wait Time 2–33
Zero Val Tolerance 2–32
Output
2f 3–6
Alarm Flags 3–5
, 3–20
Concentration 3–4
, 3–22
Date 3–1
Dry 2f 3–6
Dry 2f Ref 1 Pdry 3–6
Dry DC 3–4
, 3–6
Dry DC Ref 1 3–6
Dry Pressure 3–4
Dry Temp 3–4
Fit Ratio 3–4
Fit Ratio 2 3–4
Fit Ratio 3 3–4
Fit Ratio 4 3–4
Fit Ratio 5 3–4
Fit Ratio Dry 3–5
Fit Ratio Dry-1 3–5
Fit Residue 3–4
I-Butane 3–24
Index 3–6
Index Difference 3–4
Peak Index 3–4
Process Path Flg 3–4
Ref 0 3–6
Ref 0 RT 3–6
Ref 1 3–6
Ref 2 3–6
Ref 3 3–6
Ref 4 3–6
Ref Index 3–4
Status Flags 3–26
Time 3–1
Val Date 3–29
Val Flg 3–4
Wet 2f 3–6
Wet 2f Ref 1 Pwet 3–6
Wet DC 3–4
, 3–6
Wet DC Ref 1 3–6
Wet Pressure 3–4
, 3–29
Wet Temp 3–4
Password 2–15
, 2–37, 3–13, A–2
Powering down the analyzer 2–2
Powering up the analyzer 2–1
R
Reading diagnostic data with
HyperTerminal 3–5
Recommendations and solutions to
common problems 2–43
, A–1
RS-232 Output 3–1
S
Sample cell pressure 2–3
Sample cell temperature 2–3
Saving data from the serial port 3–5
Scroll direction 2–15
Serial port 3–5
Service contact A–4
Spectra
2
f 2–7, 3–11
DC 2–7
System Faults
Fitting Restart Alarm 2–42
Flow Switch Alarm 2–42
Laser Curnt High Alrm 2–42
Laser Curnt Low Alrm 2–42
Laser Power High Alrm 2–42
Laser Power Low Alrm 2–42
Laser Zero High Alarm 2–42
Laser Zero Low Alarm 2–43
PeakTk Restart Alarm 2–43
Pressure High Alarm 2–43
Pressure Low Alarm 2–43
Temp High Alarm 2–43
Temp Low Alarm 2–43
Validation 1 Failed/Validation 2
Failed Alarm 2–43
T
Temperature 2–3
U
Units 2–31
Concentration 2–19
Pressure 2–28
Temperature 2–31
User Alarms
Concentra High Alarm 2–43
, 3–24
Concentra Low Alarm 2–43, 3–24
To Next Page
Loading...
Need help?
General
