EWM PHOENIX 333 PROGRESS PULS forceArc - 1 Contents; Table of Contents

Contents
For your safety
4 Item No.: 099-005073-EWM01
1 Contents
1 Contents..................................................................................................................................................4
2 Safety instructions.................................................................................................................................9
2.1 For your safety ...............................................................................................................................9
2.2 Transport and installation.............................................................................................................11
2.2.1 Ambient conditions .......................................................................................................11
2.3 Notes on the use of these operating instructions.........................................................................12
3 Technical data.......................................................................................................................................13
3.1 PHOENIX 333 PROGRESS KG ..................................................................................................13
4 Machine description.............................................................................................................................14
4.1 PHOENIX 333 PROGRESS KG ..................................................................................................14
4.1.1 Front view .....................................................................................................................14
4.1.2 Rear view......................................................................................................................16
4.1.3 Inside view....................................................................................................................18
5 Functional characteristics...................................................................................................................20
5.1 Machine control – Operating elements ........................................................................................20
5.1.1 Welding machine control ..............................................................................................20
5.1.1.1 Covered operating elements.........................................................................22
5.2 MIG/MAG welding........................................................................................................................24
5.2.1 Definition of MIG/MAG welding tasks...........................................................................24
5.2.2 Selecting MIG/MAG welding tasks ...............................................................................24
5.2.2.1 Basic welding parameters.............................................................................24
5.2.2.2 Operating mode.............................................................................................24
5.2.2.3 Welding type..................................................................................................24
5.2.2.4 Choke effect / dynamics................................................................................25
5.2.2.5 Superpulses ..................................................................................................25
5.2.2.6 Wire burn-back..............................................................................................25
5.2.3 MIG/MAG operating point.............................................................................................26
5.2.3.1 Selecting the display unit ..............................................................................26
5.2.3.2 Operating point setting using material thickness, welding current, wire
speed..................................................................................................................
26
5.2.3.3 Arc length correction setting..........................................................................26
5.2.3.4 Wire burn-back..............................................................................................27
5.2.3.5 Accessory components for operating point setting .......................................27
5.2.4 MIG/MAG welding data display ....................................................................................27
5.2.5 MIG/MAG functional sequences / operating modes.....................................................28
5.2.5.1 Explanation of signs and functions................................................................28
5.2.5.2 Non-latched mode.........................................................................................29
5.2.5.3 Non-latched operation with superpulse.........................................................29
5.2.5.4 Special, non-latched......................................................................................30
5.2.5.5 Spots .............................................................................................................31
5.2.5.6 Special, non-latched with superpulse............................................................32
5.2.5.7 Latched mode................................................................................................33
5.2.5.8 Latched mode with superpulse .....................................................................34
5.2.5.9 Latched mode with alternating welding process ...........................................35
5.2.5.10 Latched special ...........................................................................................36
5.2.5.11 Latched special with welding process alternation.......................................37
5.2.5.12 Special, latched with superpulse.................................................................38
5.2.5.13 Latched special with alternating welding process.......................................39
5.2.6 MIG/MAG program sequence ("Program steps" mode)...............................................40
5.2.6.1 Selecting the program sequence parameters using wire feed unit
control M3.70......................................................................................................
40
5.2.6.2 MIG/MAG overview of parameters, M3.70....................................................41
5.2.6.3 Example, tack welding (non-latched) ............................................................42
5.2.6.4 Example, aluminium tack welding (non-latched special) ..............................42
5.2.6.5 Example, aluminium welding (latched special) .............................................43