EWM PHOENIX 333 PROGRESS PULS forceArc - Page 5

Contents
For your safety
Item No.: 099-005073-EWM01 5
5.2.6.6 Example, visible seams (latched super pulse)..............................................44
5.2.6.7 Welding process changeover........................................................................45
5.2.7 Main program A mode..................................................................................................46
5.2.7.1 Selecting parameters (program A) using wire feed unit control M3.70.........48
5.2.8 MIG/MAG automatic cut-out.........................................................................................48
5.2.9 Standard MIG/MAG torch.............................................................................................48
5.2.10 MIG/MAG special-torches ............................................................................................48
5.2.11 Special parameter, “M3.70/M3.71”...............................................................................49
5.2.11.1 Special parameters list................................................................................49
5.2.11.2 Selecting, changing and saving parameters...............................................50
5.2.11.3 Reset to factory settings .............................................................................50
5.2.11.4 Ramp time for wire inching (P1)..................................................................50
5.2.11.5 Program "0", releasing the program block (P2) ..........................................50
5.2.11.6 Display mode torch power control (P3).......................................................50
5.2.11.7 Program limit (P4).......................................................................................51
5.2.11.8 Special cycle in the operating modes special latched and non-latched
(P5)
51
5.2.11.9 Enabling special JOBs SP1 to SP3 (P6) ....................................................51
5.2.11.10 Correction operation, threshold value setting (P7) ...................................51
5.2.11.11 Program changeover with standard torch (P8).........................................52
5.2.11.12 N cycle setting...........................................................................................54
5.2.11.13 Latched/special-latched tap start (P9) ......................................................54
5.2.11.14 "Single or dual operation" (P10) setting....................................................54
5.2.11.15 Latched special tapping time setting (P11)...............................................54
5.2.11.16 JOB list switching (P12)............................................................................55
5.2.11.17 Creating user-defined JOB lists ................................................................55
5.2.11.18 Copying JOBs, "Copy to" function ............................................................56
5.2.11.19 Lower and upper limits of the remote JOB changeover process
(P13,P14) ...........................................................................................................
56
5.2.11.20 Hold function (P15) ...................................................................................56
5.2.11.21 Software key switch (SCH) .......................................................................56
5.3 TIG welding..................................................................................................................................57
5.3.1 TIG welding task selection ...........................................................................................57
5.3.2 TIG welding current setting ..........................................................................................57
5.3.3 TIG arc ignition .............................................................................................................57
5.3.3.1 Liftarc ............................................................................................................57
5.3.4 TIG function sequences / operating modes .................................................................58
5.3.4.1 Explanation of signs and functions ...............................................................58
5.3.4.2 Non-latched mode.........................................................................................59
5.3.4.3 Special, non-latched .....................................................................................59
5.3.4.4 Latched mode ...............................................................................................60
5.3.4.5 Latched special.............................................................................................61
5.3.5 TIG automatic cut-out...................................................................................................61
5.4 MMA welding ...............................................................................................................................62
5.4.1 MMA welding task selection.........................................................................................62
5.4.2 MMA welding current setting........................................................................................62
5.4.3 Arcforcing .....................................................................................................................62
5.4.4 Hotstart.........................................................................................................................62
5.4.5 Antistick ........................................................................................................................62
5.5 Interfaces .....................................................................................................................................63
5.5.1 Automation interface.....................................................................................................63
5.5.2 RINT X11 robot interface..............................................................................................64
5.5.3 BUSINT X10 Industrial bus interface............................................................................64
5.5.4 DVINT X11 Wire feed interface....................................................................................64
5.5.5 PC Interfaces................................................................................................................64
5.5.6 Setting options, internal................................................................................................64
5.5.6.1 Switching between Push/Pull and intermediate drive...................................64
5.6 Remote control.............................................................................................................................65