Fireye BurnerLogiX YB110 - User Manual

© 2023 Carrier 1
BL-1001
September 19, 2023
YB110/YB230 FIREYE
BurnerLogiX
TM
Microprocessor-Based
Integrated Burner Management Control
DESCRIPTION
The Fireye BurnerLogix
TM
System is a microprocessor-based burner management control system
designed to provide the proper burner sequencing, ignition, and flame monitoring protection on
automatically ignited oil, gas, and combination fuel burners. In conjunction with limit and
operating controls, it programs the burner/blower motor, ignition, and fuel valves to provide for
proper and safe burner operation. Through SMART LED’S, the control provides current operating
status and lockout information in the event of a safety shutdown. Optional OLED and LCD
displays are available that may be either plugged in or mounted remotely to give full language
descriptors of current status and diagnostic lockout information. Refer to BurnerLogix
PROGRAMMER SELECTION later in this document for the various combinations of
programmer and display modules.
A complete BurnerLogix system includes the YB110 (YB230) chassis equipped with the type
of flame amplifier required for the application, appropriate flame detector, plug-in programmer
module, wiring base and optional alpha-numeric display. Interchangeable programmer modules
allow for complete versatility in selection of function, timing, and flame failure response times.
The optional alpha-numeric display has 2 lines by 16 characters per line. It is available in either
vacuum fluorescent or liquid crystal formats. The advantage of OLED is high brightness and
extended temperature range down to –40°F. Both displays contain a fully functional keypad.
You can easily scroll through the various menus to view the current operating status, review
programmer configuration, and lockout history. When mounted remotely, the displays provide
NEMA 4x(IP66) protection. An advantage of the BurnerLogix control family is the ability to set
many of the operating parameters associated with proper and reliable burner operation allowing
inventory of various programmer types to be kept to a minimum.
The YB110 (YB230) is a chassis/flame amplifier module complete with mounting screws and
blank display module. The display module BLV512 (OLED) or BLL510 (LCD), if required,
must be ordered separately. Interchangeable YP programmer modules allow for complete
versatility in selection of control function, timing, and flame scanning means. Functions such as
pre-purge time, recycling or non-recycling interlocks, high fire proving interlock, and trial for
ignition timing of the pilot and main flame are determined by the programmer module. The
BurnerLogix system can be used with ultra-violet, auto-check infrared, flame rod,
self-check ultra-violet flame scanners or direct coupled integrated scanners by choosing the
proper chassis/flame amplifier module.
GEN II
GEN II

Summary

BURNERLOGIX SPECIFICATIONS

ELECTRICAL RATINGS

BURNERLOGIX ORDERING INFORMATION

INSTALLATION PROCEDURE

WIRING BASE

Describes the wiring base types and terminal details for BurnerLogix.

BEFORE INSTALLING THE BURNERLOGIX CONTROL

Provides crucial pre-installation checks and warnings for the BurnerLogix system.

INSTALLING THE YP PROGRAMMER MODULE

Details how to correctly install the YP programmer module into the YB chassis.

ELECTRICAL CHECKOUT

INSTALL BURNERLOGIX INTO WIRING BASE

BURNERLOGIX PROGRAMMER SELECTION

PTFI*MTFI TIMINGS

OPERATING CONTROL FUNCTIONS

SETTING PROGRAMMER PARAMETERS

PROGRAM SET UP SUB-MENU

FLAME SCANNERS

TO VIEW AND MODIFY A PROGRAMMABLE PARAMETER

Explains the process for viewing and changing programmable parameters on the BurnerLogix.

FLAME SCANNERS TYPES

UV SCANNERS INSTALLATION

INSTALLATION - UV SCANNERS

UV SCANNER OPERATION

INFRARED AND UV SCANNER DETAILS

INSTALLATION-INFRARED SCANNER TYPE 48 PT2

INSTALLATION - 69 ND1 FLAME ROD

INSTALLATION - 85 SERIES PHOENIX SCANNER

INSTALLATION - 95 SERIES INSIGHT SCANNERS

YP100 OPERATING SEQUENCE

START-UP (NORMAL CYCLE)

Normal Shutdown

YP200 OPERATING SEQUENCE

YP300 OPERATING SEQUENCE

PROGRAMMER WIRING DIAGRAMS

YP100;YP200 PROGRAMMERS WIRING DIAGRAM

YP300 PROGRAMMERS WIRING DIAGRAM

YP148 PROGRAMMER

YP148;YP184 PROGRAMMER DETAILS

YP148 PROGRAMMER

YP148;YP184 PROGRAMMER WIRING DIAGRAMS

LOCKOUTS AND DIAGNOSTICS

LOCKOUTS

Explains how the control indicates and handles safety shutdowns and lockouts.

DIAGNOSTIC MESSAGES

Lists diagnostic messages and their possible causes and solutions.

RESETTING THE CONTROL

Describes the methods for resetting the BurnerLogix control.

LOCKOUT CODES

Details LED codes indicating the reason for control lockout.

LOCKOUT HISTORY SUB-MENU

Allows viewing the last ten lockouts and associated cycle/hour data.

COMMUNICATIONS

CHECK RUN SWITCH

VALVE PROVING

OPERATIONAL TESTING AND PROCEDURES

OPERATIONAL TEST (BURNER COMMISSIONING)

Guides the commissioning process and operational tests for the burner.

Line Voltage Test

Normal Pilot Flame Test

Main Flame Test

Minimum Pilot Test (Pilot turn down test)

BURNERLOGIX GROUNDING RULES

Fireye BurnerLogiX YB110 Specifications

General

Category	Burner Management System
Type	Flame Safeguard Control
Manufacturer	Fireye
Model	BurnerLogiX YB110
Communication	Modbus RTU
Enclosure Rating	NEMA 4X
Flame Detection	UV, IR
Input Voltage	120 VAC
Operating Temperature	-40°C to 60°C