Flexim FLUXUS WW

To Next Page

To Previous Page

FLUXUS WW 8 Connection

56 UMFLUXUS_WWV1-1EN, 2018-02-28

Tab. 8.5: Terminal assignment (extension cable, KL2)

terminal connection

TV white or marked cable (core)

TVS white or marked cable (internal shield)

TRS brown cable (internal shield)

TR brown cable (core)

cable gland external shield

Main Page

Default Chapter2
- Umfluxus_Wwv1-1En, 20182
- Table of Contents5
1 Introduction9
- Regarding this User Manual9
- Safety Instructions9
- Warranty9
2 Safety Instructions10
- General Safety Instructions10
- Intended Use10
- Not Intended Use11
- Safety Instructions for the User11
- Safety Instructions for the Operator11
- Safety Instructions for Electrical Work11
- Safety Instructions for Transport12
- Recommended Procedure in Hazardous Situations12
- Recommended Maintenance Intervals12
3 Handling13
- First Inspection13
- General Precautions13
- Cleaning13
4 General Principles14
- Measurement System14
- Measurement Principle14
- Measurement Arrangements18
5 Description of the Transmitter21
- Transmitter Design21
- Keyboard21
6 Measuring Point Selection23
- Acoustic Penetration23
- Undisturbed Flow Profile25
- Selection of the Measurement Arrangement Taking into Account the Measuring Range and the Measuring Conditions27
- Selection of the Sound Beam Plane Near an Elbow28
7 Installation29
- Location29
- Transmitter29
- Transducers32
8 Connection49
- Transducers50
- Power Supply62
- Outputs63
- Serial Interface64
- Sensor Module (SENSPROM)65
- SD Card (Optional)66
9 Start-Up of the Transmitter67
- Start-Up Settings67
- Switching on67
- Initialization68
- Display68
- Hotcodes70
- Language Selection71
- Interruption of the Power Supply71
10 Basic Measurement72
- Input of Pipe Parameters72
- Other Parameters74
- Selection of the Channels74
- Input of the Sound Path Number75
- Transducer Distance75
- Start of Measurement77
- Detection of the Flow Direction77
- Stop of Measurement77
11 Displaying Measured Values78
- Selection of the Physical Quantity and the Unit of Measurement78
- Toggling between the Channels78
- Adjustment of the Display79
- Status Line80
- Transducer Distance81
12 Advanced Measuring Functions82
- Damping Factor82
- Totalizer82
- Settings of the Noisetrek Parallel Beam Mode83
- Settings of the Hybridtrek Mode84
- Upper Limit of the Flow Velocity85
- Cut-Off Flow85
- Uncorrected Flow Velocity86
- Measurement of High Dynamic Flows (Fastfood Mode)86
- Calculation Channels87
- Change of the Limit for the Inner Pipe Diameter89
- Diagnosis by Means of the Snap Function90
- Program Code91
13 Data Logger and Transmission of Data92
- Data Logger92
- Data Transmission95
14 Settings100
- Time and Date100
- Dialogs and Menus100
- Measurement Settings103
- Setting the Contrast104
- Instrument Information104
15 Superuser Mode105
- Activation/Deactivation105
- Transducer Parameters105
- Defining Flow Parameters105
- Limit of the Signal Amplification107
- Upper Limit of the Sound Speed107
- Detection of Long Measurement Failures108
- Number of Decimal Places of the Totalizers108
- Manual Reset of the Totalizers109
- Display of the Totalizer Sum109
- Display of the Last Valid Measured Value109
- Display During the Measurement109
16 Outputs110
- Installation of an Output110
- Error Value Delay114
- Activation of an Analog Output115
- Activation of a Binary Output as a Pulse Output116
- Activation of a Binary Output as an Alarm Output116
- Behavior of the Alarm Outputs119
- Deactivation of the Outputs121
17 Troubleshooting122
- Problems with the Measurement122
- Measuring Point Selection123
- Maximum Acoustic Contact123
- Application Specific Problems123
- Large Deviations of the Measured Values124
- Problems with the Totalizers124
- Data Transmission124
Annex125
A Menu Structure125
B Units of Measurement136
C Reference141
D Conformity Declarations144

Flexim FLUXUS WW - Page 56

Table of Contents

Related product manuals