Frecon PV Series - User Manual

PV series Solar Pumping Inverter
- 1 -
Preface
PV200 special inverters are developed for power supply of water pumps, based on the core
control arithmetic of FR200 vector control inverters, combined with the control requirements of PV
water pump application. The function of maximum power tracking, dormant at weak light, wake up at
strong light, high water level dormant, under-load pre-warning and other control protection functions
can ensure normal operation of water pumps according to the customers’ requirements to switch to the
grid power supply.
Please refer to this manual to commission the inverter, product maintenance refer to FR200 user
manual.
IMPORTANT NOTES
◆To illustrate the details of the products，pictures in this manual based on products with outer
casing or safety cover being removed. When using this product, please be sure to well install
outer casing or covering by the rules, and operating in accordance with the manual contents.
◆The illustrations in this manual are for illustration only and may vary with different products
you have ordered.
◆The company is committed to continuous improvement of products, product features will
continue to upgrade, the information provided is subject to change without notice.
◆If there is any questions when using, please contact our regional agents or our customer
service center:(+86-0755-33067999)
◆For other products, please visit our website. http://www.frecon.com.cn

Summary

Preface

Important Notes

Notes regarding product illustration, modifications, and customer support.

Chapter One Product Overview

1.1 Name Plate

Details on the inverter's identification label and its components.

1.2 Product Specifications

Technical specifications for AC220V and DC310V input products.

1.3 Dimension Drawing

Visual representation and dimensions for PV100 and PV200 series.

Chapter Two Commissioning Guide

2.1 PV Panel Power Supply Commissioning

Wiring diagrams and steps for setting up PV panel power.

2.2 Grid or Generator Power Supply Wirings

Wiring diagrams for connecting to grid or generator power.

2.3 Wiring Diagram Between VFD and Single Phase Motor

Guidance on connecting VFD with single-phase motors.

2.4 Product Terminal Configuration

Explanation of main and control circuit terminals on the inverter.

Chapter Three Function Parameters

3.1 The Basic Function Parameters

Overview of essential system and frequency-related function parameters.

3.2 H00 Group: Detailed Explanation of Function Code

In-depth explanation of PV pump special set function codes (H00 group).

Chapter Four Troubleshooting and Countermeasures

Err01 Acceleration Overcurrent

Fault due to overcurrent during acceleration and its solutions.

Err02 Deceleration Overcurrent

Fault due to overcurrent during deceleration and its solutions.

Err03 Constant-speed Overcurrent

Fault due to overcurrent at constant speed and its solutions.

Err04 Acceleration Overvoltage

Fault due to overvoltage during acceleration and its solutions.

Err05 Deceleration Overvoltage

Fault due to overvoltage during deceleration and its solutions.

Err06 Constant-speed Overvoltage

Fault due to overvoltage at constant speed and its solutions.

Err07 Bus Under voltage protection

Fault related to low bus voltage and protection measures.

Err08 Short circuit protection

Faults related to short circuits and their troubleshooting.

Err09 Input Open-phase

Fault due to open phase on input and related troubleshooting.

Err10 Output Open-phase

Fault due to open phase on output and related troubleshooting.

Err11 Motor Overload

Fault due to motor overload and its troubleshooting.

Err12 Inverter Overload

Fault due to inverter overload and its troubleshooting.

Err13 Fault protection of external input

Fault due to external input protection and its reset.

Err14 Overheat

Fault related to overheating and cooling measures.

Err15 Memory Failure

Fault caused by memory chip damage or version incompatibility.

Err16 Cancel the self-identification

Procedure for cancelling self-identification process.

Err17 Self-identification failure

Troubleshooting steps for self-identification failures.

Err18 485 Communication Timeout

Fault due to communication timeout and parameter settings.

Err19 PID feedback disconnection on running

Fault when PID feedback is lost during operation.

Err20 The running time arrives

Fault indicating the programmed running time has been reached.

Err21 Parameter Upload Error

Errors during parameter upload process.

Err22 Parameter Download Error

Errors during parameter download process.

Err23 Braking Unit failure

Faults related to the braking unit and resistor.

Err24 Disconnection Fault of temperature sensor

Fault due to temperature sensor disconnection or failure.

Err25 Inverter loss-load

Fault when inverter load is too low.

Err26 With-wave current limit fault

Fault related to current limit and load conditions.

Err27 Soft-start relay unclosed

Fault when the soft-start relay is not closed.

Err28 EEPROM Version Incompatible

Error due to EEPROM version mismatch.

Err29 Hardware detect Overcurrent

Hardware detected overcurrent fault.

Err30 Hardware detect overvoltage

Hardware detected overvoltage fault.

Err32 Hydraulic Probe Failure

Fault related to hydraulic probe malfunction.

Arn33 Pre-warning of Weak Light

Warning for low light conditions and its parameters.

Arn34 Pre-warning of Full-water

Warning for full water level and its conditions.

Frecon PV Series Specifications

General

Series	PV Series
Output Frequency	50Hz/60Hz
Protection Features	DC Reverse Polarity Protection, Over Current Protection, Over Voltage Protection, Temperature Protection
Operating Temperature Range	-25°C to +60°C
Storage Temperature Range	-40°C to 70°C
Humidity	0-95% (Non-condensing)
Communication	RS485, Wi-Fi (Optional)
Display	LCD
Certifications	CE