9-4 9. MITSUBISHI ELECTRIC
*1 For more information of “V-MDD” (dual port interface), see page 9-57.
*2 For the ladder transfer function, see the V9 Series Reference Manual.
*3 “D9-MI4-0T” is equipped with the Y-shaped terminal at the PLC side. Modification is necessary before use.
Ethernet Connection
QnA/QnH/Q170/L Series
FX3U/3UC/3G series
link
(A protocol)
FX-3G
FX3G-232BD RS-232C
Hakko Electronics’ cable
“D9-MI2-FX2N-2M”
or
Wiring diagram 3 - M2
Wiring diagram 3 - C2
FX3G-485BD RS-485
Hakko Electronics’ cable
“D9-MI4-0T”
*3
or
Wiring diagram 1 - M4
Wiring diagram 1 - C4
FX-3U
FX3U-232BD RS-232C
Hakko Electronics’ cable
“D9-MI2-FX2N-2M”
or
Wiring diagram 3 - M2
Wiring diagram 3 - C2
FX3U-485BD RS-485
Hakko Electronics’ cable
“D9-MI4-0T”
*3
or
Wiring diagram 1 - M4
Wiring diagram 1 - C4
FX-3UC
FX3U-232BD
RS-232C
Hakko Electronics’ cable
“D9-MI2-FX2N-2M”
or
Wiring diagram 3 - M2
FX3U-232ADP Wiring diagram 3 - C2
FX3U-485BD
RS-485
Hakko Electronics’ cable
“D9-MI4-0T”
*3
or
Wiring diagram 1 - M4
FX3U-485ADP Wiring diagram 1 - C4
PLC Selection on the
Editor
CPU Port Signal Level
Connection
Ladder
Transfer
*2
CN1 MJ1/MJ2
PLC Selection on the
Editor
CPU Unit TCP/IP UDP/IP Port No.
Keep
Alive
*1
Ladder
Transfer
*1
QnA series (Ethernet)
Q2A, Q3A, Q4A
AJ71QE71
AJ71QE71-B5
Auto-open: 5000
Open setting:
As desired
(max. 16 units)
Q2ASx
A1SJ71QE71-B2
A1SJ71QE71-B5
QnH (Q) series (Ethernet)
Q02, Q02H
Q06H
Q12H
Q25H
Q00J, Q00, Q01
QJ71E71 QJ71E71-B2
QJ71E71-100
Q02U
Q03UD
Q04UDH, Q06UDH
Q10UDH, Q13UDH
Q20UDH, Q26UDH
QJ71E71-B2
QJ71E71-100
Q03UDE
Q04UDEH, Q06UDEH
Q10UDEH, Q13UDEH
Q20UDEH, Q26UDEH
Q50UDEH, Q100UDEH
CPU with built-in
Ethernet
Open setting:
As desired
(max. 16 units)
QnH (Q) series (Ethernet
ASCII)
Q02, Q02H
Q06H
Q12H
Q25H
Q00J, Q00, Q01
QJ71E71 QJ71E71-B2
QJ71E71-100
Open setting:
As desired
(max. 16 units)
Q02U
Q03UD
Q04UDH, Q06UDH
Q10UDH, Q13UDH
Q20UDH, Q26UDH
QJ71E71-B2
QJ71E71-100
Q03UDE
Q04UDEH, Q06UDEH
Q10UDEH, Q13UDEH
Q20UDEH, Q26UDEH
Q50UDEH, Q100UDEH
CPU with built-in
Ethernet
To Next Page
Loading...