FUTABA 14SG S.Bus2 - Telemetry:altitude

96
<Functions of Linkage Menu>
● Select the function name
and return to the Linkage
menu by touching the
RTN button. Or the
HOME/EXIT button is
pushed.
<SensorTouch™>
RETURN
TELEMETRY : ALTITUDE
Displaying data from the altitude
ALTITUDE is a screen which displays / sets up
the altitude information from an optional altitude
sensor or GPS sensor. The altitude of the model
which is ying can be known. If it becomes higher
(low) than preset altitude, you can be told by alarm.
To show warning by vibration can also be chosen.
Data when a power supply is turned on shall be 0
m, and it displays the altitude which changed from
there. Even if the altitude of an airfield is high,
that shall be 0 m and the altitude difference from
an aireld is displayed. This sensor calculates the
altitude from atmospheric pressure. Atmospheric
pressure will get lower as you go up in altitude,
using this the sensor will estimate the altitude.
Please understand that an exact advanced display
cannot be performed if atmospheric pressure
changes in a weather situation.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest14CH mode can use all the telemetry functions.
● Select [ALTITUDE] in the TELEMETRY screen and
access the setup screen shown below by touching
the RTN button.
Scrolling
● Moving cursor
● Selecting mode
● Adjusting value
● To next page
● Altitude
● The maximum and the minimum when
powering ON are shown.
● ↓ An downward arrow
indicates the alarm
will sound when the
altitude reaches
below your set value.
● ↑ An upward arrow
indicates the alarm
will sound when the
altitude reaches
above your set value.
First, the set of a reference is required.
1. The model and transmitter to which the
altitude sensor was connected are turned on.
2. Move the cursor to the [SET] of "REFERENCE"
item and touch the RTN button to switch to
the data input mode.
3. Touch the RTN button. (To terminate the input and
return to the original state, touch the S1 button.)
*Atmospheric pressure is changed according to the weather also
at the same aireld. You should preset before a ight.
Alert set : High side
1. Move the cursor to the ↑ALERT item and
touch the RTN button to switch to the data
input mode.
2. Select the ACT mode by scrolling the touch
sensor.
3. Touch the RTN button. (To terminate the input
and return to the original state, touch the S1
button.)
4. Move the cursor to the ↑THRESHOLD [+200m]
item and touch the RTN button to switch to
the data input mode.
5. Ajust the rate by scrolling the touch sensor.
Initial value: +200m
Adjustment range: -499m~+5,000m
(↑THRESHOLD > ↓THRESHOLD)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
6. Touch the RTN button. (To terminate the input
and return to the original state, touch the S1
button.)
Alert set : Low side
1. Scroll to the second page by pushing S1. Move
the cursor to the ↓ALERT item and touch the
RTN button to switch to the data input mode.
2. Select the ACT mode by scrolling the touch
sensor.
3. Touch the RTN button. (To terminate the input
and return to the original state, touch the S1
button.)
4. Move the cursor to the ↓THRESHOLD [-50m]
item and touch the RTN button to switch to
the data input mode.
5. Ajust the rate by scrolling the touch sensor.
Initial value: -50m
Adjustment range: -500m~+4,999m
(↑THRESHOLD > ↓THRESHOLD)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
6. Touch the RTN button. (To terminate the input and
return to the original state, touch the S1 button.)
TYPE1
TYPE2
TYPE3
TYPE4
"Vibes" type
If the following types are selected, the
transmitter will vibrate during the warning.
*An altitude sensor or GPS sensor must be installed in the aircraft.
●Press the S1 button to advance to the next page.