FUTABA T16IZ SUPER

105
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
Variometer
Setsthevariometer
onwhichthealarm
operates.
↑ Anupwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
aboveyoursetvalue.
↓ Adownwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
belowyoursetvalue.
Alarmischosenfrom
Buzzer,Voice,and
Inhibit.
AllowsSpeechtobe
turnedONorOFF.
AllowsMelodytobe
turnedONorOFF.
ŏ7DSWKH>9DULRPHWHU@EXWWRQLQWKH7HOHPHWU\VFUHHQ
to call the setup screen shown below.
Max.andmin.values
sincethepower
wasturnedONwill
display.
*It cannot be used in FASST mode and S-FHSS mode.
2QO\UHFHLYHUYROWDJHDQG(;7YROWDJHFDQEHXVHGLQ
FASSTest12CH mode.
7KH)$667HVW&+7)+66PRGHFDQXVHDOOWKHWHOHPHWU\
functions.
Type1
Type2
Type3
"Vibrator"type
Ifthefollowingtypesareselected,thetransmitter
willvibrateduringthewarning.
ũƌƕƖƗŏŃƗƋƈŃƖƈƗŃƒƉŃƄŃƕƈƉƈƕƈƑƆƈŃƌƖŃƕƈƔƘƌƕƈƇő
1. The model and transmitter to which the
altitude sensor was connected are turned on.
2. Tap to the [Preset] of "Reference" item.
$WPRVSKHULFSUHVVXUHLVFKDQJHGDFFRUGLQJWRWKHZHDWKHU
DOVRDWWKHVDPHDLU¿HOG<RXVKRXOGSUHVHWEHIRUHDÀLJKW
*AnaltitudesensororGPSsensormustbeinstalledintheaircraft.
Telemetry:Altitude[Variometer]
Displaying data from the
variometer
9$5,2LVDVFUHHQZKLFKGLVSOD\VVHWVXSWKH
variometer information from an optional altitude
sensor or GPS sensor.
7KHYDULRPHWHURIWKHPRGHOZKLFKLVÀ\LQJFDQEH
NQRZQ
,ILWEHFRPHVKLJKHURUORZHUWKDQWKHVHWWLQJDQ
DODUPDQGRUYLEUDWLRQZLOODOHUW\RX
7RHQVXUHWKDWWKHSLORWLVDZDUHDVWRWKHPRGHOV
VWDWXVWKH7,=683(5LQFRUSRUDWHVDGL൵HUHQW
PHORG\IRUDVFHQWDQGGHVFHQW$GGLWLRQDOO\
GHSHQGLQJXSRQWKHUDWHRIFOLPERUGHVFHQWWKH
WRQHVYDU\WRLQGLFDWHZKHWKHURUQRWWKHDLUSODQHLV
climbing or descending at a rapid rate.
ŤƏƈƕƗŃƖƈƗŃŝŃƙƄƕƌƒƐƈƗƈƕŃ
1. Tap Alarm and choose from Buzzer, Voice,
and Inhibit.
2. Choose "Inhibit" for Vibrator if not using the
vibrator alarm. If using vibrator, choose one
of the three types.
3. Tap to the Limit [m/s] item.
$GMXVWWKHUDWHXVLQJWKHʈʈʈʆʆʆ
buttons.
Initial value: +1m
Adjustment range-50 m/s~+50 m/s
Ń/LPLW
≧
Ņ/LPLW
:KHQWKHVFUHHQLVWDSSHGIRURQHVHFRQGWKHUDWHLVUHVHW
to the initial value.
5. To terminate the input and return to the
original state, push the HOME/EXIT button.
● IfthisissettoMode1-4,
ariseanddivearetold
byadifferentmelody.
Mode1:Littlerise/dive
→ Melodychanges
:sensitively
Mode4:Bigrise/dive
→ Melodychanges
:insensible
ŏ5HWXUQWR
Linkage menu