FUTABA T16IZ SUPER

149
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
Butterfly
[Corresponding model type]: Glider, 2 ailerons or more
7KLVIXQFWLRQDOORZVSRZHUIXOEUDNHRSHUDWLRQ
by simultaneously raising the left and right
DLOHURQVDQGORZHULQJWKHIODSVFDPEHUIODS
EUDNHÀDS
7KLVVHWWLQJZLOODOORZWKHDLOHURQVWREHUDLVHG
ZKLOHWKHIODSVDUHVLPXOWDQHRXVO\ORZHUHG
%XWWHUIO\FURZSURGXFHVDQH[WUHPHO\HIILFLHQW
landing configuration by accomplishing the
IROORZLQJ
6ORZWKHDLUFUDIW·VYHORFLW\
2. Provide washout at the wing tips to reduce
the tendency to tip stall.
3. Create more lift toward the center of the
ZLQJDOORZLQJLWWRÁ\DWDVORZHUVSHHG
ŏ0L[LQJGXULQJÁLJKWFDQEHWXUQHG212))E\
setting a switch. (Always ON at [--] setting)
ŏ7KHEXWWHUÁ\RSHUDWLRQUHIHUHQFHSRLQWFDQEH
offset. When the screen is tapped with the offset
item selected when operated to the position to
be changed, the reference point is offset. If the
reference point is offset too much, unexpected
operation may be performed.
ŏ7KHDLOHURQVDQGÁDSVRSHUDWLRQVSHHGFDQEH
adjusted. (In side/Out side)
ŏ$GHOD\FDQEHVHWIRUHDFKFRQGLWLRQ$FXW
switch which can turn OFF the delay function can
also be set.
ŏ7KHGLIIHUHQWLDOUDWHFDQEHDGMXVWHG
:KHQVHUYRELQGLQJRFFXUVZKHQVHWWLQJWKHDLOHURQVDQG
ÀDSVLQEXWWHUÀ\PL[LQJXVHWKH$)5IXQFWLRQWRDGMXVWWKH
rate.
ŏ6HOHFW>%XWWHUIO\@DWWKHPRGHO
menu and call the setup screen
shown below.
*The display screen is an example. The actual
screen depends on the model type.
Whenusingthis
function,Tap[INH].
(ONisdisplayed.)
Conditiongroup/single
modeselection(Gr./
Sngl)
TheON/OFFswitchof
mixingischosen.
Conditiondelaysetting
Conditiondelaycut
switch
Tonextpage
Thedifferentialrate
canbeadjusted.
Inspeed
Outspeed
（First）0 〜 27（Slowly）
（First）0〜27（Slowly）
*Thedisplayscreenisanexample.Theactual
screendependsontheModelType.
Whenoffsettingthebutterflyoperation
referencepoint,operatetothethrottle
stickpointyouwanttochangeandthen
touchtheOffsetbutton.Thereference
pointdisplays0%.When[Yes]istouched,
thereferencepointischanged.Then,
"Initializeelevatorcurve?"appears,
allowingyoutoconfirmyoursetting.
:KHQGL൵HUHQWLDOUDWHLVWKHFDOFXODWLRQPHWKRGRI83
'2:1DQGDGLUHFWLRQEHFRPHUHYHUVH
:KHQGL൵HUHQWLDOUDWHLV8SUDWHLVGHFUHDVHDQG'2:1
rate is increase.