FUTABA T16IZ SUPER - Page 50

50
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŏ6ZDVKSODWHFRUUHFWLRQ([FHSW+PRGH
,IDQ\LQWHUDFWLRQVDUHQRWLFHGIRUDGHVFULSWLRQRIWKH
OLQNDJHFRUUHFWLRQIXQFWLRQSOHDVHUHIHUWRWKH6:$6+
function.
ŘőŃŷƋƕƒƗƗƏƈŒųƌƗƆƋŃƆƘƕƙƈŃƖƈƗƗƌƑƊ
7KLVIXQFWLRQDGMXVWVWKHWKURWWOHRUSLWFKRSHUDWLRQ
curve in relation to the movement of the throttle
stick for each condition.
<Throttle curve setting example>
&DOOWKHWKURWWOHFXUYHRIHDFKFRQGLWLRQZLWKWKH
FRQGLWLRQVHOHFWVZLWFK
ŏ1RUPDOFXUYHDGMXVWPHQW
Normal curve creates a basic throttle curve
centered near hovering. This curve is adjusted
together with the pitch curve (Normal) so that the
engine speed is constant and up/down control is
easiest.
ŏ,GOHXSFXUYHDGMXVWPHQW
The low side Throttle curve creates a curve
matched for aerobatics (loop, roll, 3D, etc.).
ŏ7KURWWOHKROGFXUYHDGMXVWPHQW
The curve is not used when performing auto rotation
dives.
&RQÀUPWKDWWKHUDWHRIWKHVORZHVWSRVLWLRQRI
WKHVWLFNLVLQLWLDOVHWWLQJ
<Example of pitch curve setting>
&DOOWKHSLWFKFXUYHRIHDFKFRQGLWLRQZLWKWKH
FRQGLWLRQVHOHFWVZLWFK
ŏ3LWFKFXUYH1RUPDO
Make the pitch at hovering approximately +5
º
~6
º
.
Set the pitch at hovering with the stick position at
WKHSRLQWDVWKHVWDQGDUG
*Stability at hovering may be connected to the throttle curve.
$GMXVWPHQWLVHDV\E\XVLQJWKHKRYHULQJWKURWWOHIXQFWLRQ
and hovering pitch function together.
ŏ3LWFKFXUYH,GOHXS
The idle up 1 pitch curve function creates a curve
PDWFKHGWRDLUERUQHÁLJKW
Set to -7
º
~+12
º
as standard.
ŗőŃũƘƖƈƏƄƊƈŃƏƌƑƎƄƊƈ
&RQQHFWWKHWKURWWOHUXGGHUDLOHURQHOHYDWRU
SLWFKDQGRWKHUVHUYRVLQDFFRUGDQFHZLWKWKH
kit instruction manual. For a description of the
FRQQHFWLRQPHWKRGVHH6HUYRVFRQQHFWLRQE\
model type".
Note: The channel assignment of the T16IZ
SUPER is different from that of our existing
systems. (The channel assigned to each
function can be checked at the Function
menu of the Linkage menu.)
ŏ,IWKHGLUHFWLRQRIRSHUDWLRQRIWKHVHUYRLV
incorrect, use the Reverse function of the
Linkage menu. Also use the swash AFR
function in other than the H-1 mode.
ŏ$GMXVWWKHGLUHFWLRQRIRSHUDWLRQRIWKHJ\UR
(Gyro side function)
ŏ&RQQHFWWKHWKURWWOHOLQNDJHVRWKDWWKH
carburetor can fully close at full trim throttle
cut.
ŏ$GMXVWWKHQHXWUDOSRVLWLRQDWWKHOLQNDJH
VLGHDQGÀQHWXQHZLWKWKH6XE7ULPIXQFWLRQ
and End point function (rudder angle
adjustment). To protect the linkage, a limit
position can also be set with the End point
function.