FUTABA T16IZ SUPER

80
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŏ7DSWKH>)DLOVDIH@EXWWRQLQWKH/LQNDJHPHQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZ
Failsafe
Sets the servos' operating position when transmitter signals can no
longer be received or when the receiver battery voltage drops.
The Fail safe function is used to set up positions
WKDWWKHVHUYRVZLOOPRYHWRLQWKHFDVHRIUDGLR
LQWHUIHUHQFH'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUH
ORVWDQGZKHQUHFHLYHUEDWWHU\YROWDJHEHFRPHVORZ
<RXPD\VHWHLWKHURIWZRSRVLWLRQVIRUHDFKFKDQQHO
+ROGZKHUHWKHVHUYRPDLQWDLQVLWVODVWFRPPDQGHG
SRVLWLRQRUIDLOVDIHZKHUHHDFKVHUYRPRYHVWR
DSUHGHWHUPLQHGSRVLWLRQ<RXPD\FKRRVHHLWKHU
mode for each channel.
7KH7,=683(5V\VWHPDOVRSURYLGHV\RXZLWK
DQDGYDQFHGEDWWHU\PRQLWRULQJIXQFWLRQWKDWZDUQV
\RXZKHQWKHUHFHLYHUEDWWHU\KDVRQO\DOLWWOH
SRZHUUHPDLQLQJ,QWKLVFDVHHDFKVHUYRLVPRYHG
WRWKHGH¿QHGIDLOVDIHSRVLWLRQ7KHEDWWHU\IDLOVDIH
PD\EHUHOHDVHGE\RSHUDWLQJDSUHGH¿QHGFRQWURO
RQWKHWUDQVPLWWHUGHIDXOWLVWKURWWOH'RQRW
FRQWLQXHWRÀ\/DQGDVVRRQDVSRVVLEOH5HPHPEHU
if the predefined control suddenly moves to a
ũƄƌƏŃƖƄƉƈŃƖƈƗƗƌƑƊŃƓƕƒƆƈƇƘƕƈ
'HFLGHZKLFKFKDQQHOV\RXZDQWWRJRWRSUHVHW
SRVLWLRQVDQGZKLFKRQHV\RXZDQWWRPDLQWDLQ
their last commanded position. To select the fail
VDIHPRGH\RXZLVKWRVHWXVHWKH)6EXWWRQ7KLV
EXWWRQWRJJOHVEHWZHHQWKHWZRPRGHV+ROG)6
F/S mode setting:
1. Tap the F/S button of the channel you want
to set, and set that channel to the [F/S]
mode.
2. Hold the corresponding stick, control, slider,
or other control in the position you want the
servo to move to when the fail safe function
is activated, and tap the F/S position button.
That position is displayed in percentage.
:KHQ\RXZDQWWRUHWXUQWKDWFKDQQHOWRWKH+ROGPRGHWDS
WKH>)6@EXWWRQDJDLQ
ťƄƗƗƈƕƜŃƉƄƌƏŃƖƄƉƈŃƖƈƗƗƌƑƊŃƓƕƒƆƈƇƘƕƈ
7RVHOHFWWKH%)6PRGHWDSWKH>%)6@EXWWRQ
(DFKWLPHWKHEXWWRQLVWDSSHGLWWRJJOHVEHWZHHQ
>2))@DQG>%)6@
B.F/S setting:
SRVLWLRQ\RXGLGQRWFRPPDQGODQGDWRQFHDQG
check your receiver battery.
'RQRWFRQWLQXHWRIO\/DQGDVVRRQDVSRVVLEOH
'HILQHVVHUYRSRVLWLRQZKHQVLJQDOVDUHORVWDQG
ZKHQUHFHLYHUEDWWHU\YROWDJHEHFRPHVORZ
WARNING

Forsafety,alwayssetthefailsafefunctions.
Ŷ(VSHFLDOO\VHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDWWKH
VHUYRPRYHVWRWKHPD[LPXPVORZVLGHIRUDLUSODQHVDQGWRWKH
VORZVLGHIURPWKHKRYHULQJSRVLWLRQIRUKHOLFRSWHUV&UDVKLQJ
RIWKHPRGHODWIXOOKLJKZKHQQRUPDOUDGLRZDYHVFDQQRWEH
UHFHLYHGGXHWRLQWHUIHUHQFHHWFLVYHU\GDQJHURXV
Ŷ,IIDLOVDIHLVUHVHWE\WKURWWOHVWLFNPRYHPHQWWKHIDLOVDIH
PD\EHPLVWDNHQDVDQHQJLQHPDOIXQFWLRQDQGZLOOEHUHVHW
DWORZWKURWWOHDQGWKHPRGHOZLOOFRQWLQXHWRÀ\,I\RXKDYH
DQ\GRXEWVLPPHGLDWHO\ODQG
1. Tap the [B.F/S] button of the desired channel
to set it to the B.F/S mode.
2. Hold the corresponding stick, VR, slider,
or other control in the position you want
the servo to move to when the battery fail
safe function is activated, and tap the F/S
position button. This position is displayed in
percentage.
:KHQ\RXZDQWWRUHWXUQWKDWFKDQQHOWR2))WDSWKH>%)6@
button again.
ťƄƗƗƈƕƜŃũƄƌƏŃƖƄƉƈŃƕƈƏƈƄƖƈŃƉƘƑƆƗƌƒƑ
7KLVIXQFWLRQUHOHDVHVWKHSUHGH¿QHGFRQWUROIURP
its held position after indicating that your receiver
EDWWHU\LVORZ
1. Enter the control setting screen by tapping
the Battery F/S release button. Now, you may
choose whether moving the throttle resets
the condition, or select a stick or switch to
deactivate it. To set a desired throttle release
position, move the throttle stick to the point
at which you wish the B.F/S to be released.
ŏ5HWXUQWR
Linkage menu