GE C70 - Page 697

INDEX
C70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUAL xi
Product information
actual values .......................................................................................6-27
Device Connectivity Report in Engineer .................................4-76
firmware revision ..............................................................................6-27
Programmed mode ............................................................................3-48
Protection elements ............................................................................. 5-4
Protection Summary interface .............................3-63, 4-4, 5-252
Protocol selection ................................................................................5-50
Prototype firmware error message ...........................................7-15
PRP
actual values .......................................................................................6-11
explained ..............................................................................................5-46
settings ..................................................................................................5-44
specifications ......................................................................................2-31
PTP
actual values for port state ............................................................ 6-8
clock settings ...................................................................................5-107
error message ....................................................................................7-12
port behavior ......................................................................................5-45
settings ...............................................................................................5-108
specifications ......................................................................................2-31
pu quantity ................................................................................................5-4
Pushbuttons
control FlexLogic ............................................................................5-165
control logic diagram ..................................................................5-122
control settings ...............................................................................5-121
control specifications ......................................................................2-24
testing ...................................................................................................... 7-7
user-programmable FlexLogic ................................................5-176
user-programmable logic diagrams ....................................5-127
user-programmable settings ...................................................5-123
user-programmable specifications .........................................2-24
Q
Quick Connect ...........................................................................3-63, 3-64
R
RADIUS server
authentication ....................................................................................5-15
setup .........................................................................................................B-1
RAM required ..........................................................................................3-50
Reactive power .....................................................................................6-18
Reactive power specifications .....................................................2-25
Real power ...............................................................................................6-18
Real power specifications ...............................................................2-25
Real-time clock
actual values for synchronization .............................................. 6-8
FlexAnalogs ........................................................................................ A-32
settings ...............................................................................................5-107
Reboot relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-7
Recloser curves ...................................................................5-158, 5-195
Redundancy
PRP actual values .............................................................................6-11
PRP explained ....................................................................................5-46
settings .................................................................................................5-44
specifications .....................................................................................2-31
Relay architecture ............................................................................5-162
Relay maintenance ...............................................................................7-7
Relay name ...........................................................................................5-138
Release Notes .....................................................................................10-14
Remote access of front panel in EnerVista .................4-17, 6-3
Remote access, explained ................................................................5-8
Remote Setting Authorization ....................................................10-14
Repair ................................................................................... 1-2, 10-29, D-1
Replace battery ..................................................................................10-24
Replace battery message ..............................................................7-11
Replace front panel .........................................................................10-15
Replacement modules .....................................................................2-13
Requirements for installation .......................................................3-50
Reset alarm ...............................................................................................6-4
Reset to factory defaults .......................................................5-7, 5-21
Resetting
FlexLogic operands .......................................................................5-175
setting to clear LEDs and messages .....................................5-298
to factory defaults ..............................................................................5-7
Restart relay
using EnerVista ....................................................................................5-1
using relay ..............................................................................................7-7
Restore settings ...................................................................................10-8
Revision history ...................................................................................... D-1
RF immunity specifications ...........................................................2-34
RFI, conducted specifications ......................................................2-34
R-GOOSE description ........................................................................5-65
RJ-45 .................................................................................................2-8, 3-12
RMS voltage specifications ............................................................2-25
Roles for login ...........................................................................................2-5
Routable GOOSE ..................................................................................5-65
RS232
baud rate .............................................................................................5-41
configuration ...................................................................................... 3-63
specifications .....................................................................................2-30
wiring .....................................................................................................3-33
RS422
configuration ...................................................................................... 3-43
timing .....................................................................................................3-44
two-channel application ..............................................................3-43
RS485
description ........................................................................................... 3-35
limitation with CyberSentry .........................................................5-16
port on rear panel ............................................................................3-12
settings .................................................................................................5-41
specifications .....................................................................................2-30
RTD FlexAnalogs ..................................................................................A-30
RTD inputs
actual values ......................................................................................6-23
settings ...............................................................................................5-306
Rules for passwords .............................................................................5-8