GE C70 - Page 696

x C70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUAL
INDEX
Passwords
authentication by device or server .......................................... 5-15
bypass authentication ................................................................... 5-22
change .................................................................................................. 4-58
change after installation .............................................................. 3-65
change does not take relay out of service .............................5-1
command .......................................................................4-58, 5-9, 5-10
default ................................................................................................... 5-13
explained ................................................................................................2-4
FlexLogic operands .......................................................................5-175
lockout ...................................................................................... 4-59, 5-13
lost password .......................................................................................5-7
requirements ........................................................................................5-8
reset to factory defaults ..................................................................5-7
rules ...........................................................................................................5-8
settings ............................................................................4-58, 5-9, 5-10
settings templates ..............................................................................4-7
wrong entry ........................................................................................ 4-59
Permissive functions .......................................................................5-235
Per-unit quantity ....................................................................................5-4
Phase angle metering ...................................................................... 6-13
Phase current balance FlexAnalogs ........................................ A-31
Phase current metering .................................................................. 6-16
Phase current unbalance
actual values ...................................................................................... 6-21
commands .............................................................................................7-4
FlexLogic operands .......................................................................5-168
logic diagram ...................................................................................5-204
settings ...............................................................................................5-201
specifications ..................................................................................... 2-20
theory of operation ......................................................................... 9-11
Phase directional overcurrent
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-201
phase A polarization .....................................................................5-199
settings ...............................................................................................5-198
specifications ..................................................................................... 2-19
Phase IOC
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-198
settings ...............................................................................................5-197
specifications ..................................................................................... 2-19
Phase overvoltage
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-237
settings ...............................................................................................5-236
specifications ..................................................................................... 2-21
Phase rotation ....................................................................................5-141
Phase TOC
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-197
settings ...............................................................................................5-195
specifications ..................................................................................... 2-18
Phase undervoltage
FlexLogic operands .......................................................................5-171
logic diagram ...................................................................................5-236
settings ...............................................................................................5-235
specifications ..................................................................................... 2-21
Phasor display graphical front panel ..........................4-56, 5-31
Plastic film on front panel ........................................................... 10-20
Port
Ethernet, turn on or off ..................................................................5-44
failure monitoring ............................................................................5-37
HTTP, close ..........................................................................................5-99
IEC 60870-5-104, close ............................................................... 5-101
Modbus, close ....................................................................................5-50
on rear panel ......................................................................................3-12
SNTP, close ....................................................................................... 5-111
TFTP, close ........................................................................................ 5-100
USB ..........................................................................................................4-16
Port number
combinations with protocols ......................................................5-50
connectivity report of those used ............................................4-76
DNP .........................................................................................................5-51
HTTP ........................................................................................................5-99
IEC 60870-5-104 ............................................................................ 5-100
list of .......................................................................................................5-44
Modbus .................................................................................................5-49
Modbus during installation ..........................................................3-60
RADIUS ..................................................................................................5-18
SNTP .................................................................................................... 5-111
system log ...............................................................................5-18, 5-19
TFTP ..................................................................................................... 5-100
Power metering
specifications .....................................................................................2-25
values .....................................................................................................6-18
Power off, save data first ................................................................3-16
Power supply
description ...........................................................................................3-15
diagram ................................................................................................3-12
LED on module ..................................................................................3-16
removal to replace battery ....................................................... 10-24
specifications .....................................................................................2-27
wire size ................................................................................................3-15
Power system settings .................................................................. 5-141
Precision Time Protocol
actual values for port state ............................................................6-8
clock settings .................................................................................. 5-107
error message ...................................................................................7-12
port behavior ......................................................................................5-45
settings ............................................................................................... 5-108
specifications .....................................................................................2-31
Preferences
comparing settings .........................................................................10-7
Engineer ................................................................................................4-76
IEC 61850 .............................................................................................5-60
import file .............................................................................................10-9
Preserve custom attributes when importing SCD/CID files ..
10-9
Print front panel labels .........................................................4-43, 4-75
Process bus
order codes for compatible URs ..................................................2-8
overview ...............................................................................................3-18