gefran ADV200 SP Series - Appendix 1 - Miscellaneous; A 1.1 DC-Link Capacity

106 pages

To Next Page

To Previous Page

104 ADV200 SP • Quick start up guide - Specification and installation

Appendix 1 - Miscellaneous

A 1.1 DC-link capacity

Size

DC-link capacity

(µF)

1015 235

1022 235

1030 340

1040 340

1055 340

2075 680

2110 680

2150 840

3185 1500

3220 1500

3300 1500

4370 2350

4450 2800

4550 3400

5750 4700

5900 5600

51100 6800

61320 11200

61600 13600

You cannot add an external capacitor on 1015 ... 61600 sizes.

Attention

Main Page

Information about this Manual2
Table of Contents3
Safety Precautions5
Symbols Used in the Manual5
Safety Precaution6
General Warnings6
Instruction for Compliance with UL Mark (UL Requirements), U.S. and Canadian Electrical Codes7
Introduction to the Product9
Drive Type Designation10
Transport and Storage11
General11
Permissible Environmental Conditions12
Disposal of the Device12
Mechanical Installation13
Inclination and Mounting Clearance13
Fastening Positions14
Wiring Procedure17
Power Section20
Cable Cross Section20
Connection of Shielding21
EMC Guide Line22
Block Diagram Power Section22
Power Line Connection23
Input Mains Choke (L1)24
Motor Connection24
Braking Unit Connection (Optional)24
Parallel Connection of Several Inverters25
Connection of Fans25
Regulation Section26
Removing the Terminal Cover26
Cable Cross Section26
Regulation Section Connection26
Switches, Jumpers and LED28
Braking30
Braking Unit30
Serial Interface (XS Connector)32
Drive / RS 485 Port (Not Insulated) Point-To-Point Connection32
Drive / RS485 Port Point-To-Point Connection (with Insulation)33
RS 485 Multi-Drop Connection34
Typical Connection Diagrams36
Use of the Keypad40
Description40
Navigation41
Scanning of the First and Second Level Menus41
Display of a Parameter41
Scanning of the Parameters42
List of the Last Parameters Modified42
Goto Parameter" Function42
Parameter Modification42
How to Save Parameters43
Configuration of the Display44
Language Selection44
Selection of Easy / Export Mode44
Startup Display44
Back-Lighting of the Display44
Alarms45
Alarm Reset45
Messages45
Saving and Recovery of New Parameter Settings46
Selection of the Keypad Memory46
Saving of Parameters on the Keypad46
Load Parameters from Keypad46
Transfer of Parameters between Drives47
Commissioning Via Keypad (STARTUP WIZARD)48
Startup Wizard and Dedicated Settings51
Programming59
Menu Display Modes59
Programming of "Function Block" Analog and Digital Input Signals59
Variable Interconnections Mode59
Multiple Destination61
Troubleshooting62
Alarms62
Messages66
Specification70
Environmental Conditions70
Standards70
Accuracy (Asyncronous)70
Current Control70
Speed Control70
Speed Control Limits71
Torque Control71
Overload71
DC Circuit71
Input Electrical Data72
AC Power Supply72
DC Power Supply72
Output Electrical Data73
Output Current Derating Factors74
Overload for Output Frequency76
Voltage Level of the Inverter for Safe Operations77
Cooling77
Weight and Dimensions77
Options86
DC-Side Diode86
Diodes Selection86
Diodes and Weight Dimensions86
Mounting Instructions and Precautions91
Spds (Surge Protection Devices)93
DC-Side SPD Devices93
AC-Side SPD Devices93
Insulation Monitor94
Contactors94
DC-Side Contactors94
AC-Side Contactors94
Fuses95
AC Input Side Fuses95
DC Fuses on the Inverter Side for Short-Circuit Protection95
EMI Filters97
EMI Filters for IT Network Connections97
EMI Filters for TT or TN Network Connections98
EMI Filters for DC Connections99
Radiation Sensor99
Braking Resistor (Optional)100
Installation of Optional Cards101
Procedure102
Shielding of Optional Card Connections103
Appendix 1 - Miscellaneous104
A 1.1 DC-Link Capacity104

Related product manuals

gefran ADV200 WA DC Series

gefran TPD32-EV-...-4B

504 pages

gefran TPD32-EV-500 series

504 pages

gefran TPD32-EV-CU series

504 pages

gefran ADV200 SP Series - Appendix 1 - Miscellaneous; A 1.1 DC-Link Capacity

Table of Contents

Related product manuals