Gendex GX CB-500 - Chapter 14 - Illustrated Parts Breakdown

218 pages

To Next Page

To Previous Page

14-1

G990710 30 June 2008

Chapter

Illustrated Parts Breakdown

WARNINGWARNING

High voltage is present in the device. Remove power from device

before removing covers or cables. To avoid personal injury from

electrical shock, do not operate the system with any covers open or

cables removed.

This chapter is used to provided replacement part numbers. Ensure

power is removed before servicing the device.

The following Assemlies are illustrated.

• System Assembly

• Overhead Assembly

• Chair Assembly

• Upper Chair Assembly

• Upper Chair Assembly Parts List

• X-Ray Source Assembly

• Receptor Panel Assembly

Main Page

Default Chapter3
- Table of Contents3
Chapter 1 - Introduction9
- System Description9
- Major System Items10
- About the Operators' Manual11
  - Conventions Used in the User Manual11
- Standard Limited Warranty12
Chapter 2 - Safety Items15
- Important Safety Information15
- System Safety Devices20
- Sample Site Plan21
  - Interlock and Warning System Schematic22
- Cabling Requirements23
- Emergency Removal of a Patient23
- System Labels24
- Error Messages27
Chapter 3 - System Controls and Indicators29
- Operator Control Box29
- Patient Emergency Stop Control30
- Patient Alignment Panel30
- System Status Indicators30
Chapter 4 - System Startup and Shutdown31
- System Startup31
- System Shutdown31
Chapter 5 - System Assembly33
- Initial Preparation33
- Required Tools33
- Abbreviations33
- Inventory of Unit Items34
- System Assembly36
Chapter 6 - Leveling and Alignment49
- Level Gantry49
- Patient Chair Alignment52
- Laser Alignments56
  - Adjust Centerline Laser56
  - Adjust Crosshair Laser59
- Head Holder Alignment62
Chapter 7 - Calibration63
- Panel Calibration63
- Collimators Calibration65
- Geometry Calibration66
Chapter 8 - Quality Assurance71
- QA Phantom Test71
- QA Water Phantom Test80
- PAN Phantom Test90
- Radiation Output Test93
  - Measured Dose93
  - Interpretation94
Chapter 9 - Troubleshooting and Adjustments95
- Detector Pivot Adjustment (Receptor Panel)95
- IEC IC Command Codes97
  - Home Commands97
  - Movement Commands97
- Read Commands98
- X-Ray Commands100
- Miscellaneous Commands101
Chapter 10 - Wall Mount Control Box103
- Wall Mount with Cable Exposed103
- Wall Mount with Cable Inside Wall106
Chapter 11 - Networking Support Setup111
- Networking Support Overview111
- Networking Data Flow111
- Network Support Installation/Setup112
- Sweeper Service116
  - Sweeper Controller116
- Network Failures117
  - No Network Access at Startup117
  - Network Fails During Operations118
- Limitations of Networking Support119
Chapter 12 - Remote System Import and Export121
- Remote System Import and Export Overview121
- Remote System Import121
- Import Installation and Setup122
  - Set up DICOM Worklist Interface122
  - Set up Practice Management Interface124
- Import Patient Data125
- Remote System Export126
- Export Installation and Setup126
- RSSM Log128
- Send Patient Data to a Remote System129
Chapter 13 - Product Information131
- Technical Specifications131
- Power Requirements132
  - Apparent Resistance of Supply Mains132
- Weight133
- Power Cords Required Outside of the United States133
- Environmental Specifications134
  - Operating134
  - Transportation and Storage134
- Acquisition Computer134
- Patient Support Chair135
- Disposal135
- Extension Cords135
- External Item135
- Cleaning135
- Electromagnetic or Other Interference (Emissions and Immunity)136
- Equipment Standards138
- Equipment Class138
- Preventive Maintenance Schedule - for Owner / User139
- Planned Maintenance - 12 Month Schedule139
  - Cleaning140
  - Planned Maintenance Checklist140
- Replaceable Parts - Reference List142
- Accessories143
Chapter 14 - Illustrated Parts Breakdown147
- System Assembly148
  - System Assembly Parts List149
- Overhead Assembly150
  - Overhead Assembly Parts List151
- Rotation Drive Assembly152
  - Rotation Drive Assembly Parts List153
- X-Ray Source Assembly154
  - X-Ray Source Assembly Parts List155
- Receptor Panel Assembly156
  - Receptor Panel Assembly Parts List157
- Chair Assembly158
  - Chair Assembly Parts List159
- Upper Chair Assembly160
  - Upper Chair Assembly Parts List161
Chapter 15 - Radiation Environment Survey163
- Conditions of Operation - 8.9 and 23.0 Second Scans164
- Scatter Measurements for 8.9 Second Scans165
  - Standard (Full-Beam) Diameter 8.5 - Height 8.5 CM165
  - Half Beam Diameter 14 - Height 8.5 CM167
- Scatter Measurements for 23 Second Scans169
  - Standard (Full-Beam) Diameter 8.5 - Height 8.5 CM169
  - Half Beam Diameter 14 - Height 8.5 CM Scan170
- Scatter Measurements for PAN Scan171
- Scan Times and Settings173
- Dose and Imaging Performance Information174
- Dose Profile175
- Sensitivity Profile177
- Drywall Attenuation178
- Recommended Operating Requirements179
- X-Ray Tube Assembly180
Appendix A - Icatvision, Icattransfer, & RSQM Installation185
- Icatvision185
- Icattransfer189
- Rsqm192
- RSQM Installation and Setup192
- Query and Retrieve Images194
- Status Messages197
Appendix B - I-Catvision Release Notes199
Appendix C - Assembly Report Form Sample209
Appendix D - System Schematics211

Gendex GX CB-500 - Chapter 14 - Illustrated Parts Breakdown

Table of Contents

Related product manuals