GW Instek GDS-1062A - Probe Specifications; GDS-1062 A;1102 A;1152 A Probe; EC Declaration of Conformity

APPENDIX
121
Probe Specifications
GDS-1062A/1102A/1152A Probe
Applicable model &
probe
GDS-1062A
GTP-060A-4*
GDS-1102A
GTP-100A-4*
Position x 10 Attenuation Ratio 10:1
Bandwidth DC ~ 60MHz DC ~ 100MHz
Input Resistance 10MΩ when used with 1MΩ input
Input Capacitance 23pF approx.
17pF approx.
Maximum Input
Voltage
500V CAT I, 300V CAT II (DC+Peak AC)
Derating with frequency
Position x 1 Attenuation Ratio 1:1
Bandwidth DC ~ 6MHz
Input Resistance 1MΩ when used with 1MΩ input
Input Capacitance 128pF approx. 47pF approx.
Maximum Input
Voltage
300V CAT I, 150V CAT II (DC+Peak AC)
Derating with frequency
Operatin
g
Cond. Temperature –10°C ~ 55°C
Relative Humidity ≤85% @35°C
Safety Standard EN 61010-031 CAT II
Applicable model &
probe
GDS-1152A GTP-150A-2*
Position x 10 Attenuation Ratio 10:1
Bandwidth DC ~ 150MHz
Input Resistance 10MΩ when used with 1MΩ input
Input Capacitance 17pF approx.
Maximum Input
Voltage
500V CAT I, 300V CAT II (DC+Peak AC)
Derating with frequency
Position x 1 Attenuation Ratio 1:1
Bandwidth DC ~ 6MHz
Input Resistance 1MΩ when used with 1MΩ input
Input Capacitance 47pF approx.
Maximum Input
Voltage
300V CAT I, 150V CAT II (DC+Peak AC)
Derating with frequency
Operating Cond. Temperature –10°C ~ 55°C
Relative Humidity ≤85% @35°C
Safet
y
Standard EN 61010-031 CAT II
* Note: GW Instek reserves the right to change the probe model type (GTP-060A-4,
GTP-100A-4, GTP-150A-2) at anytime without notice for probe model types of similar
specification.
GDS-1000A Series User Manual
122
EC Declaration of Conformity
We
GOOD WILL INSTRUMENT CO., LTD.
No.7-1, Jhongsing Rd., Tucheng City, Taipei County 236, Taiwan
GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.
No. 69, Lushan Road, Suzhou New District Jiangsu, China
declares that the below mentioned product
GDS-1062A, GDS-1102A, GDS-1152A
Are herewith confirmed to comply with the requirements set out in the
Council Directive on the Approximation of the Law of Member States
relating to Electromagnetic Compatibility (2004/108/EC) and Low
Voltage Equipment Directive (2006/95/EC). For the evaluation
regarding the Electromagnetic Compatibility and Low Voltage
Equipment Directive, the following standards were applied:
◎ EMC
EN 61326-1 :
EN 61326-2-1:
Electrical equipment for measurement, control and
laboratory use –– EMC requirements (2006)
Conducted and Radiated Emissions
CISPR11: 2003+A1: 2004+A2: 2006
Electrostatic Discharge
IEC 61000-4-2: 2001
Current Harmonic
EN 61000-3-2: 2006
Radiated Immunity
IEC 61000-4-3: 2006+A1: 2007
Voltage Fluctuation
EN 61000-3-3: 1995+A1: 2001+A2 : 2005
Electrical Fast Transients
IEC 61000-4-4: 2004+Corr.1 : 2006+Corr.2 :
2007
-------------------------
Surge Immunity
IEC 61000-4-5: 2005
-------------------------
Conducted Susceptibility
IEN 61000-4-6: 2003+A1: 2004+A2: 2006
-------------------------
Power Frequency Magnetic Field
IEC 61000-4-8: 2001
-------------------------
Voltage Dips/ Interrupts
IEC 61000-4-11: 2004
◎ Safety
Low Volta
g
e E
q
ui
p
ment Directive 2006/95/EC
Safety Requirements
IEC/EN 61010-1: 2001