HellermannTyton Autotool 2000 CPK - Page 4

Operating Instructions • AT2000 CPK • 07-2019 • v03 • 106-29004 4
9.3 Binding menu ................... 18
9.3.1 Entering password ................ 18
9.3.2 Select a language ................ 18
9.3.3 Synchronising time and date ........ 19
9.3.4 Display binding information ......... 19
9.3.5 Select parameter set .............. 19
9.3.6 Set interruption front sensor ........ 19
9.3.7 Setting the binding check .......... 19
9.3.8 Activating consecutive trigger ....... 19
9.3.9 Status indicators ................. 19
9.4 Service menu .................... 20
9.4.1 Updating service information ........ 20
9.4.2 Changing the access code in the
AT2000 CPK .................... 20
9.5 Memory menu. . . . . . . . . . . . . . . . . . . 21
9.5.1 Refresh memory of the tool ......... 21
9.5.2 Limit the time period of the bindings .. 21
9.5.3 Limit the time period of the
messages ...................... 22
9.5.4 Select bindings .................. 22
9.5.5 Select messages ................. 22
9.5.6 Read and export the process data
on the HTDM ................... 22
9.5.7 Export data ..................... 22
9.5.8 Display exported data in the HTML
format ......................... 22
9.6 Update menu ................... 23
9.6.1 Update firmware ................. 23
9.6.2 Change password ................ 24
9.6.3 Update binding parameters ......... 24
9.6.4 Install other languages. . . . . . . . . . . . . 24
9.7 Measurement environment menu .... 25
9.7.1 Using measurement mode .......... 25
9.7.2 Deleting measurement results ....... 26
9.7.3 Saving measurement results ......... 26
9.8 Parameter set menu. . . . . . . . . . . . . . . 27
9.8.1 Synchronise parameter sets ......... 27
9.8.2 Save parameter sets ............... 28
9.8.3 Load parameter sets .............. 28
9.9 Export process data from the power
packCPK ....................... 29
10 Troubleshooting ................... 29
10.1 Important notes ................. 29
10.2 Performing a reset ................ 30
10.3 Display messages ................. 30
10.4 Possible fault .................... 33
10.4.1 Troubleshooting a cable-tie bandoleer
malfunction ..................... 33
10.4.2 Changing back-up battery .......... 34
11 Maintenance ...................... 34
11.1 Important notes ................. 34
11.2 Accessories and extras ............. 34
11.3 Servicing by manufacturer .......... 35
11.4 Maintenance schedule ............. 35
11.5 Repair ......................... 35
11.5.1 Checking upper jaw ............... 35
11.5.2 Replacing upper jaw .............. 35
11.5.3 Checking front cap and position of
cutter ......................... 36
11.5.4 Checking tie advancer ............. 36
11.5.5 Replacing tie advancer ............. 36
12 Technical data ..................... 37
12.1 AT2000 CPK .................... 37
12.2 PowerpackCPK ................. 38
12.3 Noise and vibration information ...... 38
13 Declarations of conformity ........... 39
13.1 AT2000 CPK automatic tool system ... 39
13.2 Power pack CPK ................. 40