Honeywell CIPer 50 - Installation & Commissioning Instructions Manual

85 pages

To Next Page

® U.S. Registered Trademark

31-00233-02

CIPer

MODEL 50 CONTROLLER

INSTALLATION & COMMISSIONING INSTRUCTIONS

DECEMBER 2020

Main Page

Table of Contents3
Safety Information6
General Safety Information6
Information as Per en 607306
WEEE Directive7
Standards and Approvals7
Specifications of Controller7
System Overview8
Overview of Hardware8
System Architecture10
Bus and Port Connections11
Overview11
Legend12
RS232 / RJ45 Socket12
Configuring the RS232 Interface in Webs N413
USB 2.0 Host Interface13
USB 2.0 Device Interface14
Ethernet / RJ45 Sockets14
Separated Networks15
Switch Networks15
Default IP Addresses of Ethernet Interfaces 1 and 217
Leds17
RS485 Interfaces17
RS485-2 Bias and Termination Resistors20
RS485 Standard20
Modbus Connection21
Wiring Topology21
Cables21
Shielding22
RS485 Repeaters22
Modbus Master Specifications22
Set up and Configuration23
Configuring Ports to Enable Webserver Functions26
Firmware Update28
Mounting and Dismounting29
Dimensions29
Wiring and Set-Up30
General Safety Considerations30
Fusing Specifications30
Lightning Protection30
Wiring Terminals31
Terminal Assignment31
Power Supply33
Powering Ciper Model 5033
Transformer Data34
Powering Panel Bus I/O Modules and Field Devices35
Powering Field Devices and Panel Bus I/O Module Via Separate Transformers35
Powering Field Devices Via Panel Bus I/O Module35
WEB-EHSERIESNX26X Connection Examples36
Internal I/Os of the Ciper Model 5037
Universal Inputs37
Slow Binary Input Specifications39
Pulse Counter Specifications39
Analog Outputs40
Binary Inputs / Pulse Counters40
Binary Outputs42
Engineering and Commissioning43
Required Preparations43
Option 1: USB 2.0 Device (Recommended)43
Option 2: Standard Ethernet Interface43
Behavior of Outputs During Download43
Additional Parts44
Software Licenses and Upgrades45
Panel Bus Connection46
Overview of Panel Bus I/O Modules46
Panel Bus Considerations46
Connecting Ciper Model 50 Via Its RS485-1 Interface to a Panel Bus47
Connecting Ciper Model 50 Via Its RS485-2 Interface to a Panel Bus48
Addressing Panel Bus I/O Modules49
Automatic Updating of Panel Bus I/O Module Firmware49
Cable Specifications50
Panel Bus I/O Modules50
EIA 485 Cable Specifications50
Tuning Panel Bus Communication50
Field Devices52
Routing Cables to Field Devices52
Lonworks Communications53
General Information53
Connecting to a LON WORKS Network53
Cable Types53
If-Lon253
Bacnet MS/TP Bus Connection55
Bacnet MS/TP Bus Considerations55
Connecting Ciper Model 50 Via RS485-1 Interface to a Bacnet MS/TP Bus55
Connecting Ciper Model 50 Via RS485-2 Interface to a Bacnet MS/TP Bus57
Modbus Connection58
Modbus Considerations58
Connecting Ciper Model 50 Via RS485-1 Interface to a Modbus58
Connecting Ciper Model 50 Via RS485-2 Interface to a Modbus59
M-Bus Connection61
M-Bus Considerations61
Bus Length61
Wiring Topology61
Cabling Ciper Model 50 to PW3/PW20/PW6061
Cabling PW3/PW20/PW60 to M-Bus62
M-Bus Connection Procedure63
Controller Performance66
Troubleshooting67
Ciper Model 50 Controller Troubleshooting67
Power LED (Green) of Ciper Model 5067
Status LED (Red) of Ciper Model 5067
L1 Led68
L2 Led68
Tx and Rx Leds69
Panel Bus I/O Module Troubleshooting69
Appendix 1: Earth Grounding70
Ciper Model 50 Systems and SELV70
Ciper Model 50 Systems and Standard EN60204-170
General Information70
Earth Grounding of EN60204-1 Applicable Systems70
Sensor Input Accuracy73
Recognition of Sensor Failure of Sensor Inputs73
Sensor Characteristics74
NTC 20 Kω (Type II) Temperature Characteristics74
NTC 10 Kω (Type II) Temperature Characteristics77
NI1000 TK6180 DIN B Temperature Characteristics79
NI1000 TK5000 DIN B Temperature Characteristics80
BALCO 500 Temperature Characteristics81
PT1000 Temperature Characteristic (PT1000-1, PT1000-2)83
Index85

Honeywell CIPer 50 - Installation & Commissioning Instructions Manual

Table of Contents

Other manuals for Honeywell CIPer 50

Related product manuals