EasyManuals Logo

HP 280 G3 User Manual

HP 280 G3
116 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #52 background imageLoading...
Page #52 background image
Computer Setup—Security
NOTE: Support for specic Computer Setup options may vary depending on the hardware conguration.
Option Description
Setup Password Allows you to set and enable a setup (administrator) password.
NOTE: If the setup password is set, it is required to change Computer Setup options, ash the ROM, and
make changes to certain plug and play settings under Windows.
Power-On Password Allows you to set and enable a power-on password. The power-on password prompt appears after a
power cycle or reboot. If the user does not enter the correct power-on password, the unit will not boot.
Password Options
(This selection appears
only if a power-on
password or setup
password is set.)
Allows you to enable/disable:
Lock Legacy Resources (determines whether or not Windows Device Manager is allowed to change
resource settings for serial and parallel ports).
Stringent security (enabling the stringent password disables the ability to reset the password by
moving the jumper on the system board). Default is disabled.
CAUTION: If you enable the stringent security feature and you forget the setup password or the
power-on password, the computer is inaccessible and can no longer be used.
If you lose or forget the password, the system board must be replaced. This scenario is not covered
under warranty.
To prevent the computer from becoming permanently unusable, record your congured setup
password or power-on password in a safe place away from your computer. Without these
passwords, the computer cannot be unlocked.
Setup Browse Mode (appears if a setup password is set) (allows viewing, but not changing, the F10
Setup Options without entering setup password). Default is enabled.
Password prompt on F9 & F12 (requires setup password to use these boot functions). Default is
enabled.
Network Server Mode. Default is disabled.
Device Security Allows you to set Device Available/Device Hidden (default is Device Available) for:
System audio
NOTE: Set this value to ‘Device hidden’ to disable all system volume.
Network controller
NOTE: You must disable AMT before trying to hide the network controller.
SATA ports (varies by model)
USB Security Allows you to set Enabled/Disabled (default is Enabled) for:
Rear USB Ports
Internal USB Ports
Slot Security Allows you to disable any M.2 slot. Default is enabled.
Network Boot Enables/disables the computer’s ability to boot from an operating system installed on a network server.
Default is enabled.
System IDs Displays the following:
Product name.
Serial number.
44 Chapter 5 Computer Setup (F10) Utility

Table of Contents

Other manuals for HP 280 G3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP 280 G3 and is the answer not in the manual?

HP 280 G3 Specifications

General IconGeneral
Memory slots2x DIMM
Internal memory8 GB
Memory clock speed2666 MHz
Internal memory typeDDR4-SDRAM
Maximum internal memory32 GB
Tjunction100 °C
Processor cache9 MB
Processor cores6
System bus rate8 GT/s
Processor familyIntel® Core™ i5
Processor socketLGA 1151 (Socket H4)
Processor frequency3 GHz
Processor cache typeSmart Cache
Processor lithography14 nm
Processor manufacturerIntel
PCI Express slots version3.0
Processor boost frequency4.4 GHz
Processor operating modes64-bit
PCI Express configurations1x8+2x4, 1x16, 2x8
Thermal Design Power (TDP)65 W
Number of processors installed1
Maximum number of PCI Express lanes16
Memory bandwidth supported by processor (max)41.6 GB/s
Maximum internal memory supported by processor128 GB
HDD speed7200 RPM
HDD interfaceSATA
Storage mediaHDD
Total HDDs capacity1000 GB
Card reader integrated-
On-board graphics cardYes
On-board graphics card ID0x3E92
On-board graphics card modelIntel® UHD Graphics 630
Maximum on-board graphics card memory64 GB
On-board graphics card OpenGL version4.5
On-board graphics card base frequency350 MHz
On-board graphics card DirectX version12.0
On-board graphics card dynamic frequency (max)1100 MHz
Number of displays supported (on-board graphics)3
Microphone inNo
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity2
USB 3.2 Gen 1 (3.1 Gen 1) Type-C ports quantity0
Chassis typeSFF
Product colorBlack
Placement supportedHorizontal/Vertical
Product typePC
Motherboard chipsetIntel® H370
HP segmentBusiness
Ethernet LAN data rates10, 100, 1000 Mbit/s
Power supply180 W
Scalability1S
Processor ARK ID134895
Processor package size37.5 x 37.5 mm
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal solution specificationPCG 2015C
Weight and Dimensions IconWeight and Dimensions
Depth296 mm
Width95 mm
Height270 mm
Weight4200 g

Related product manuals