HP ProLiant ML150 User Manual

Troubleshooting
BIOS Reset/Update/Recovery
Should you experience compatibility or stability issues with the HP server, HP recommends
starting the troubleshooting by first updating the system BIOS, which may fix the current
problem. If the BIOS has become corrupt, it is possible to perform a BIOS reset, recovery, or
update to correct the condition. A BIOS update/recovery diskette is created when the most
current BIOS is downloaded from the HP website to be used in flashing the BIOS on the
server. To perform a reset, an update, or a BIOS recovery, perform one of the following
procedures.
BIOS Reset
If the HP server needs the BIOS settings set to the factory defaults (the HP recommended
values) due to possible corruption, perform the following steps. The default values have been
selected to optimize the HP server’s performance.
NOTE: It is recommended that the system’s setup and configuration settings be noted before resetting
the system to the defaults in the BIOS Setup Utility.
1. Reboot the HP server in a normal manner and press the Delete key to enter the BIOS
Setup Utility.
2. Press the F9 key to load default values.
3. Press the F10 key to save changes and exit the BIOS Setup Utility.
BIOS Update/Recovery
Use this procedure to update the HP server system BIOS with the latest BIOS version. HP
regularly posts a new version of the HP server BIOS on the website to improve the HP
server’s performance.
1. Provide a blank, formatted 3 ½” floppy diskette.
2. Insert this diskette to any Windows PC with HTML browser and a connection to the
Internet.
http://www.hp.com
3. Locate and download the latest HP server BIOS to the PC’s hard drive. Double-click on
the file and follow the instructions to extract the file to the floppy diskette. This
downloaded BIOS on the diskette becomes the BIOS update diskette.
HP ProLiant ML150 Server Operations and Maintenance Guide 4-7
HP CONFIDENTIAL Codename: Stone Soup Part Number: 343329-001 Last Saved On: 8/14/03 10:25 AM

HP ProLiant ML150 Specifications

General

Tcase	72.8 °C
Bus type	QPI
Stepping	R2
FSB Parity	No
Scalability	2S
Processor cache	15 MB
Processor cores	6
Processor model	E5-2603V3
System bus rate	6.4 GT/s
Processor series	Intel Xeon E5-2600 v3
Processor socket	LGA 2011-v3
Processor codename	Haswell
Motherboard chipset	Intel C610
Number of QPI links	2
Processor frequency	1.6 GHz
Processor cache type	Smart Cache
Processor lithography	22 nm
Processor manufacturer	Intel
Processor package size	52.5 x 45 mm
Processor front side bus	- MHz
Processor operating modes	64-bit
ECC supported by processor	Yes
PCI Express configurations	x4, x8, x16
Supported instruction sets	AVX 2.0
Thermal Design Power (TDP)	85 W
Number of processors installed	1
Physical Address Extension (PAE)	46 bit
Maximum number of PCI Express lanes	40
Memory types supported by processor	DDR4-SDRAM
Memory channels supported by processor	Quad
Memory clock speeds supported by processor	1600 MHz
Memory bandwidth supported by processor (max)	51 GB/s
Maximum internal memory supported by processor	768 GB
HDD size	- \
RAID support	-
HDD interface	Serial ATA
Total storage capacity	0 GB
Maximum storage capacity	- TB
Number of HDDs installed	0
Memory slots	16x DIMM
Internal memory	4 GB
Memory clock speed	2133 MHz
Maximum internal memory	256 GB
Memory layout (slots x size)	1 x 4 GB
Graphics card family	NVIDIA
Intel® Virtualization Technology (Intel® VT)	VT-d, VT-x
Ethernet interface type	Gigabit Ethernet
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	4
Chassis type	Rack (1U)
Power supply	550 W
Processor ARK ID	83349
Intel Secure Key Technology version	1.00
Intel Identity Protection Technology version	0.00
PCI Express slots version	3.0

Weight and Dimensions

Depth	620 mm
Width	200 mm
Height	432.6 mm
Weight	22230 g