Huawei PowerCube 1000

To Next Page

To Previous Page

● All conductive metal components inside the enclosure should properly

connect to protection ground terminals.

PowerCube 1000 (STC, Saudi Arabia, ICC800-A1-C2,

ESC800-A1)

Installation Guide 6 Cable Routing Requirements

Main Page

About this Document3
Table of Contents5
Safety Precautions9
General Safety9
Personnel Requirements13
Electrical Safety14
Installation Environment Requirements15
Mechanical Safety17
Battery Safety20
PV Module Safety23
DG Safety23
Solution Scenarios27
Component28
PV Module Support28
PV Module (52240257)29
Sjb-0601A30
Icc800-A1-C232
Esc800-A136
Etp48600-C5B139
DC Output Box41
Lithium Battery Bus Bar Box DCDB48-650-13B42
Junction Box for Lithium Batteries43
AC Input Module AIU03-100C44
Smu02C44
User Interface Module UIM05D149
DG Expansion Module GIM50
Psu53
Ssu55
Power Module M48500N156
Pvdu-150A159
Antenna60
Digital Temperature and Humidity Sensor61
Smoke Sensor63
Water Sensor63
Esm-48100A664
Installing PV Modules71
Installation Preparations72
Preparing Cables72
Preparing Tools73
Installation Space Requirements74
Cabinet Cable Hole Positions and Definitions76
Cable Routing Requirements77
Installing the Cabinet80
Marking Mounting Holes80
Drilling Holes and Installing Expansion Sleeves81
Hoisting a Cabinet82
Installing Cabinets on a Concrete Floor85
Optional) Installing Right and Left Sealing Plates85
Combining Cabinets86
Removing Sealing Plates86
Securing Cabinets87
Installing Connecting Kits88
Installing a Top Sealing Plate90
Installing a Ground Cable92
Installing Components94
Component Installation Positions94
Installing a PSU96
Installing a Power Module M48500N197
Installing a DG Expansion Module98
Installing an AC Input Module99
Installing a PVDU-150A1100
Installing an SSU101
Installing a Digital Temperature and Humidity Sensor102
Installing Batteries and Cables104
Installing Lithium Batteries105
Installing Battery Cables106
Installing Battery Cables between the Battery Cabinet and the ICC Cabinet111
Installing Cables113
Installing a Dry Contact Signal Cable113
Optional) Installing Communications Cable114
IP Networking114
Wireless Networking114
BBU In-Band Networking115
Installing Cables for the PVDU-150A1116
Installing CAN Communications Cables120
Installing Cables between the ESC800 and the ICC800120
Installing Cables for a Reused DG123
Installing DC Output Power Cables for the ETP48600-C5B1125
Installing AC Input Power Cables for the ETP48600-C5B1126
Installation Verification127
Power-On and Commissioning129
Connecting the Reused DG Supply129
Setting Parameters130
Setting the Display Language130
Setting Wizard130
Setting the Date and Time131
Setting Intelligent Circuit Breaker Parameters131
Setting the Usage of Intelligent Circuit Breakers131
Setting the Capacity of a Circuit Breaker132
Setting the Branch User and Load Type133
Setting Customized Load Disconnection Parameters133
Setting the PVDU Power Cascading Port Parameters135
Setting the Power Input Parameters135
Setting 57 V Constant Voltage Output Parameters136
Setting the Number of Dgs136
Setting Parameters for the Reused DG136
Setting Sensor Parameters140
Setting Multiplexed Dry Contact Ports Type141
Setting Communications Parameters142
Optional) Setting Communications Addresses for Air Conditioners145
Starting the DG Self-Check147
Connecting the PV Supply148
Connecting the Lithium Battery Supply149
Connecting the Load Supply149
Checking before Leaving the Site150
Optional) Installing Front and Rear Sealing Plates150
Installing Front and Rear Sealing Plates for Combined Cabinets151
Subsequent Operations152
A Appendix154
Operating Environment154
Associations between UIM Dry Contacts and Alarms155
Preparing Terminals156
Installing Floating Nuts157

Huawei PowerCube 1000 - Page 79

Table of Contents

Related product manuals