FCC AND ISED CANADA FOR WIRELESS KEYPADS
WARNING: To comply with FCC and ISED Canada RF exposure compliance requirements, the
HS2LCDRFPRO9 or HS2LCDWFPRO9, and HS2LCDWFVPRO9 keypads should be located at a
distance of at least 20 cm from all persons during normal operation. The antennas used for
this product must not be co-located or operated in conjunction with any other antenna or
transmitter. This device complies with FCC Rules Part 15 and with ISED Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2)this device must accept any interference that may be
received or that may cause undesired operation.
IC:160A – HS2KRFP9
Models: HS2LCDRFPRO9, HS2LCDWFPRO9, HS2LCDWFVPRO9 (operating in 912-919MHz band) are
compliant with applicable FCC Part 15.247 and IC RSS-210 rules.
The term “IC” before the radio certification number only signifies that ISED Canada technical
specifications were met.
Avertissement: Pour répondre aux exigences de conformité de la FCC et ISDE Canada sur les
limites d'exposition aux radiofréquences (RF), les clavier HS2LCDRFPRO9 ou HS2LCDWFPRO9,
HS2LCDWFVPRO9 doivent être installés à une distance minimale de 20 cm de toute personne lors
de leur fonctionnement usuel. Ces derniers ne doivent pas être situés au même endroit, ni être en
fonction avec une autre antenne ou un autre transmetteur. Le present appareil est conforme aux
CNR ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee
aux deux conditions suivantes: (1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible
d'en compromettre le fonctionnement.
EN Compliance
This product meets the requirements of Class II, Grade 3 equipment as per EN 50131-1:2006
+ A1:2009 +A2:2017 Standard. This product is suitable for use in systems with the following
notification options:
- A (use of two remotely powered warning devices and single path SP3 internal dialer or Ethernet
path or plug-in cellular module required),
- B (self powered warning device (wireless siren) and single path SP3 internal dialer or Ethernet
path or plug-in cellular module required),
- C (dual path DP2 internal dialer and alternate Ethernet or plug-in cellular communicator required)
- D (single path SP4 internal Ethernet path or plug-in cellular communicator with encryption
enabled required)
- E (dual path DP3 internal Ethernet path and plug-in cellular communicator required)
The Model HS3032, HS3128, and HS3248 Control panels have been certified by Telefication
according to EN50131-1:2006 + A1:2009 +A2:2017, EN50131-3:2009 Type B, EN50131-6:2017 Type
A, EN50131-10:2014 and EN50136-2:2013 for Grade 3, Class II, ATS Configurations SP3 (phone line
path only), SP4 (Ethernet or cellular path only), DP2 (dual path with phone line primary path and
Ethernet or Cellular secondary path) and DP3 (dual path with Ethernet or Cell primary path and
Cellular or Ethernet as secondary path.
EUROPEAN CE COMPLIANCE STATEMENT
This product is in conformity with the Electromagnetic Compatibility Directive 2014/30/EU, the Low
Voltage Directive 2014/35/EU, and the ROHS3 Directive (EU)2015/863.
Simplified EU Declaration of Conformity
49PowerSeries Pro HS3032/HS3128/HS3248 User Manual
To Next Page
Loading...
