IMPORTANT
SAFETY
INSTRUCTIONS
Putting sewing systems into operation is prohibited untilit has been ascertained that the sewing systems in
which
these
sewing machines
will
be built into, have conformed with the safety regulations in your country.
Technical service for
those
sewing
systems
is also prohibited.
1. Observe
the
basic safety measures, including, but not limited to the following
ones,
whenever you
use
the
machine.
2. Read all the instructions, including, but not limited to this Instruction Manual before you
use
the machine.
In addition,
keep
this
Instruction Manual
so
that
you
may
read
it at anytime
when
necessary.
3.
Use
the
machine
after
it
has
been
ascertained
that
it
conforms
with
safety
rules/standards
valid in
your
country.
4. Allsafety devices must be in position when
the
machine is ready for work or in operation.
The
operation
without
the
specified
safety
devices
is not allowed.
5.
This
machine
shall
be
operated
by
appropriately-trained
operators.
6. For
your
personal
protection, we
recommend
that
you
wear
safety
glasses.
7. For
the
following,
turn
off
the
power switch
or
disconnect
the
power plug of
the
machine from
the
receptacle.
7-1 For
threading
needle(s), looper,
spreader
etc.
and
replacing bobbin.
7-2 For replacing part(s) of needle, presserfoot, throat plate, looper, spreader, feed dog, needle guard, folder,
cloth
guide
etc.
7-3
For
repair
work.
7-4 When leaving
the
working
place
or when
the
working
place
is
unattended.
7-5 When using clutch motors without applying brake, it
has
to be waited until
the
motor
stopped
totally.
8. Ifyou should allow oil, grease, etc.
used
with the machine
and
devices to come in contact with your
eyes
or
skin or swallow any of
such
liquid by mistake, immediately
wash
the
contacted
areas
and
consult a medical
doctor.
9. Tampering with
the
live
parts
and
devices,
regardless
of whether
the
machine is powered, is prohibited.
10. Repair, remodeling
and
adjustment
works
must
only be
done
by appropriately trained
technicians
or
specially skilled
personnel.
Only
spare
parts
designated
by JUKI
can
be
used
for repairs.
11. General
maintenance
and
inspection
works
have
to be
done
by
appropriately
trained
personnel.
12. Repair
and
maintenance works of electrical
components
shall be
conducted
by qualified electric
technicians
or
under
the
audit
and
guidance
of
specially
skilled
personnel.
Whenever you find a failure of
any
of electrical
components,
immediately
stop
the
machine.
13. Before making repair
and
maintenance works on
the
machine equipped with pneumatic parts
such
as
an air
cylinder,
the
air
compressor
has
to be
detached
from the machine and
the
compressed
air supply
has
to be
cut
off. Existing residual air
pressure
after
disconnecting
the
air
compressor
from
the
machine
has
to be
expelled.
Exceptions
to
this
are
only
adjustments
and
performance
checks
done
by appropriately trained
technicians
or
specially
skilled
personnel.
14.
Periodically
clean
the
machine
throughout
the
period
of
use.
15. Grounding
the
machine
is always
necessary
for
the
normal
operation
of
the
machine.
The
machine
has
to
be
operated
in
an
environment
that
is free from
strong
noise
sources
such
as
high-frequency welder.
16. An
appropriate
power plug
has
to be
attached
to
the
machine by electric technicians. Power plug
has
to be
connected
to
a
grounded
receptacle.
17.
The
machine
is
only
allowed
to
be
used
for
the
purpose
intended.
Other
used
are
not
allowed.
18. Remodel
or
modify
the
machine
in
accordance
with
the
safety
rules/standards
while taking all
the
effective
safety
measures.
JUKI
assumes
no responsibility for
damage
caused
by remodeling
or
modification of
the
machine.
19.
Warning
hints
are
marked
with
the
two
shown
symbols.
A
Danger
of
injury
to
operator
or
service
staff
A
Items
requiring
special
attention
V
To Next Page
Loading...
