Keba KeDrive D3-DA BG3 - Ambient Conditions, Power Reduction, and Certifications

74
1 Appendix
Operation Manual KeDrive D3-DA BG3 and BG4
1804.200B.1-01 Date: 03/2023
Appendix
A.4 Ambient conditions
Ambient conditions KeDrive D3-DA axis controllers BG3 and BG4
Degree of protection Device: IP20 - exception terminals: IP00
Health and safety regulations As per the local regulations (e.g.DGUV V3 in Germany)
Installation altitude
Up to 1000 m aboveMSL, higher with power reduction
(1% per 100m, max. 3000m aboveMSL)
Pollution degree 2 as per EN60664-1
Type of mounting
Built-in unit, only for vertical mounting in a switch cabinet with min. degree of
protection IP4x, if STO safety function used min. IP54
Table A.4 Ambient conditions, KeDrive D3-DA axis controllers BG3 and BG4
Climatic conditions KeDrive D3-DA axis controllers BG3 and BG4
In transit
As per EN61800-2, IEC60721-3-2 class 2K3
1)
Temperature -25°C to +70°C
Relative atmospheric
humidity
95% at max. +40 °C
In storage
As per EN61800-2, IEC60721-3-1 classes 1K3 and 1K4
2)
Temperature -25°C to +55°C
Relative atmospheric
humidity
5 to 95%
In operation
As per EN61800-2, IEC60721-3-3 class 3K3
3)
Temperature 5°C to +40°C (4, 8, 16kHz), to 55°C with power reduction
Relative atmospheric
humidity
5 to 85% without condensation
1) The absolute humidity is limited to max. 60g/m³. This means, at 70°C for example, that the relative atmospheric humidity may only be max. 40%.
2) The absolute humidity is limited to max. 29g/m³. So the maximum values for temperature and relative atmospheric humidity stipulated in the table must
not occur simultaneously.
3) The absolute humidity is limited to max. 25g/m³. That means that the maximum values for temperature and relative atmospheric humidity stipulated in the
table must not occur simultaneously.
Table A.5 Climatic conditions, KeDrive D3-DA axis controllers BG3 and BG4
NOTE:
The climatic conditions apply to the device. For this reason they must also be
met in the switch cabinet.
Mechanical conditions KeDrive D3-DA axis controllers BG3 and BG4
Vibration limit in transit
As per EN61800-2, IEC60721-3-2 class 2M1
Frequency [Hz] Amplitude [mm] Acceleration [m/s²]
2≤f<9 3.5 Not applicable
9≤f<200 Not applicable 10
200≤f<500 Not applicable 15
Shock limit in transit
As per EN61800-2, IEC60721-3-2 class 2M1
Drop height of packed device max. 0.25m
Vibration limits for the
system
1)
As per EN61800-2, IEC60721-3-3 class 3M1
Frequency [Hz] Amplitude [mm] Acceleration [m/s²]
2≤f<9 0.3 Not applicable
9≤f<200 Not applicable 1
1) The devices must not be installed in areas where they are exposed to continuous vibration.
Table A.6 Mechanical conditions, KeDrive D3-DA axis controllers BG3 and BG4
CAUTION! Damage to the device due to incorrect operation!
Failure to observe the ambient conditions may result in damage.
• No continuous vibration!
The axis controllers must not be installed in areas where they would be permanently
exposed to vibration.
• Switch cabinet min. IP54 for STO and SBC! as per ENISO13849-2
• Observe cooling conditions!
NOTE:
The devices are only designed for stationary use.