EasyManua.ls Logo

Kzyee KM301 User Manual

Default Icon
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
OBDII /CAN SCAN TOOL
- 1 -
Question and Answer IconNeed help?

Do you have a question about the Kzyee KM301 and is the answer not in the manual?

Kzyee KM301 Specifications

General IconGeneral
BrandKzyee
ModelKM301
CategoryScanner
LanguageEnglish

Summary

Owner's Manual and Safety Instructions

General Safety Precautions

Essential warnings and precautions for safe operation, handling, and maintenance of the scan tool.

Warning Symbols and Definitions

Danger and Warning Symbols

Definitions for hazard symbols indicating risks of death or serious injury.

Important Safety Information

General Safety Guidelines

Comprehensive safety precautions for operating the scan tool on vehicles.

Setup - Before Use

Operating Instructions

Connecting the Scan Tool

Step-by-step guide for securely connecting the scan tool to the vehicle's DLC.

Initial Power-Up and Communication Checks

Procedures after connecting, including ignition status and handling linking errors.

Performing a Battery Test

Initiating the Battery Test

Steps to navigate the menu and begin the battery testing procedure.

Battery Test Procedure Details

Setting Test Standards and AH Value

Inputting battery specifications like CCA and AH for precise testing.

Viewing Battery Test Results

How to interpret the displayed outcomes and status of the battery test.

Battery Test Result Interpretation

Good Battery and Rechargeable States

Explanation of 'Good Battery' and 'Good, Recharge' results and their implications.

Battery Replacement and Retest Scenarios

Covers 'Replace' and 'Charge, Retest' outcomes, indicating battery condition.

Bad Cell Condition Identification

Description of 'Bad Cell, Replace' result and necessary actions.

Cranking Test Procedure

Connecting for Cranking Test

Proper procedure for connecting test clamps to the vehicle battery terminals.

Executing and Viewing Cranking Test

Steps to start the engine and interpret the cranking test results.

Charging System and Ripple Test

Performing the Ripple Test

Steps to conduct the ripple test and view real-time voltage readings.

Loaded and Unloaded Voltage Tests

Procedures for testing charging system under load and no load conditions.

Charging Test Result Interpretation

Normal, Low, and High Charging Voltages

Explanation of common charging voltage results and their implications.

No Volt Output and Diode Test Results

Description of no output scenarios and diode test interpretation.

Quick Test Function

Initiating Quick Test and Inputting Capacity

Steps to start the Quick Test and input the battery's rated capacity (AH).

Diagnostic Test Modes Overview

Mode $01-$04 Descriptions

Explains modes for powertrain data, freeze frame, DTCs, and clearing codes.

Diagnostic Trouble Codes (DTCs)

Types of DTCs

Explains Pending, Stored, and Permanent DTC classifications.

I/M Readiness Quick-Check

Performing the Readiness Check

Steps to initiate and conduct the I/M Readiness Quick-Check for emissions tests.

Interpreting Readiness Results

Explanation of icons, symbols, and LED interpretations for readiness status.

Accessing the Diagnostic Menu

Connecting and Initializing for Diagnostics

Steps to connect the tool and turn on the ignition for diagnostic access.

Reading Trouble Codes

Selecting Code Types for Reading

Options to read Stored, Pending, or Permanent DTCs.

DTC Lookup Function

Erasing Diagnostic Trouble Codes

Erasing Codes Procedure

Step-by-step guide for clearing emission-related DTCs after repairs.

Live Data Viewing

Recording Live PID Data

Data Recording and Playback

Playback Live PID Data

Freeze Frame Data Viewing

Accessing Freeze Frame Data

Retrieving and viewing operating conditions captured when a DTC occurred.

I/M Readiness Status

02 Monitor Test

On-Board Monitor Test

Component Test Function

Executing Component Tests

Steps to command the PCM for tests like Evaporative Leak Test.

Software and DTC Library Update