Lantech IPES-5408T User Manual

9
Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast
packet only and all types of packet.
The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet
limit.
PTP v2 & RTC
Support hardware-based IEEE1588 PTPv2 in 1μs with 4 x GigaT ports
Built-in RTC(Real Time Clock) to keep track of time
Flow Control
Supports Flow Control for Full-duplex and Back Pressure for Half-duplex
Environmental Monitoring
System status for input voltage, current and ambient temperature to be shown in GUI and sent alerting if any abnormal status
System Log
Supports System log record and remote system log server
SMTP/Text SMS
Supports SMTP Server and 6 e-mail accounts for receiving event alert; can send SMS text alert via mobile
Relay Alarm
Provides one relay output for port breakdown, power fail and alarm.
Alarm Relay current carry ability: 1A @ DC24V
Protection
 Miss-wiring avoidance
 Repowered auto ring restore(Node failure protection)
 Loop protection
SNMP Trap
Up to 3 trap stations; trap types including:
 Device cold start
 Authorization failure
 Port link up/link down
 Abnormal environmental monitoring
DHCP
Provide DHCP Client/ DHCP Server/ relay Option 82*
DNS
Provide DNS client feature and support Primary and Secondary DNS server.
SNTP
Supports SNTP to synchronize system clock in Internet
Firmware Update
Supports TFTP firmware update, TFTP backup / InstaConfig** firmware upgrade / backup for multiple switches
Configuration
upload and download
Supports text configuration file for system quick installation
IfAlias
Each port allows an alphabetic string of 128-byte assigned as its own unique name via the SNMP or CLI interface
*Future release
**Optional
IPES-5408T-8 series
Hardware Specification
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base T
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE802.3at/af Power over Ethernet
Switch Architecture
Back-plane (Switching Fabric): 9.6Gbps
Packet throughput ability (Full-Duplex): 23.8Mpps @64bytes
Transfer Rate
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Fiber Ethernet port
Mac Address
16K MAC address table
Jumbo frame
10KB for 10/100TX ports
Connector
10/100TX: 8 x M12 4-pole D-coded with auto MDI/MDI-X function
10/100/1000T: 4 x M12 8-pole A-coded with auto
MDI/MDI-X function
RS-232 connector: 1 x M12 5-pole A-coded
Power Input connector : 1 x M23 5-pole A-coded
Relay contact : 1 x M12 5-pole A-coded
Network Cable
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
1000BaseT : 4-pair UTP/STP Cat 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
Protocol
CSMA/CD
PoE pin assignment
RJ-45 port # 1~#8 support IEEE 802.3at End-point, Alternative A mode. Per port provides 30W (802.3at) at 53~56VDC ; 15W
(802.3af) at 48V~56VDC.
Positive (VCC+): RJ-45 pin 1,2.
Negative (VCC-): RJ-45 pin 3,6.
LED
Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red)
Ethernet port: Link/Activity (Green), Speed (Green); GigaT: Link/Activity (Green)

Lantech IPES-5408T Specifications

General

Brand	Lantech
Model	IPES-5408T
Category	Switch
Language	English