Lenze 9300 vector Series - Page 458

Appendix
Index
13
13.2

13.2-5
EDSVF9333V EN 1.0-09/2004
Residual hazards, 2.3-1
Running optimisation, 6.11-1
S
Safe standstill, 11-1
- Active function, 5.9-3
- additional safety instructions, 11.1-1
- automatic cyclic monitoring with PLC, 11.4-2
- deactivated function, 5.9-6
- internal wiring, 11.2-1
Safety instructions, 2-1
- definition, 2.4-2
- design, 2.4-2
- for ”safe standstill”, 11.1-1
Safety relay, connector X11
- terminal assignment, 11.3-1
- wiring, 11.3-1
Safety relay KSR
- Terminal assignment, 5.9-8
- terminal assignment, 11.3-2
Selecting the operating mode, speed mode, setting
acceleration and deceleration times, 6.10-3
Selection, operating mode, 6.1-1 , 6.8-1
Selection of motor type, 6.6-1 , 8.2-29 , 8.2-52 , 8.3-9
Selection of the feedback system, 6 .7-1 , 8.2-50 , 8.3-4
Setting integral action component, 8.2-59
Setting the acceleration time, 6.10-3
Setting the deceleration time, 6.10-3
Setting the feedback system, 6.7-1
Setting the speed feedback, 6.7-1
Slip compensation, 6.11-1 , 8.2-47 , 8.2-75
Specific resistance (CAN), 5.10-1
Speed control, 8.2-34 , 8.2-58
- adapting the speed controller, 8.2-58
- at v ector control (MCTRL2), adapting the speed
controller, 8.2-34
-withvectorcontrol(MCTRL2)
setting integral action component, 8.2-59
speed feedback, 8.2-58
temperature detection, 8.2-59
Speed feedback, 8.2-58
Speed mode, setting acceleration and d eceleration times,
6.10-3
Speed oscillations, 6.11-3
Speed setpoint limitation, 8.2-33 , 8.2-57
Speed setpoint selection, 8.2-33 , 8.2-57
Stability, of the motor, 8.2-60
Status word AIF, 8.3-15 , 9.1-2
Stopping, 6.10-1
Supply forms, 3.1-2
Switching frequency, automatic current-depending
change-over, 6.9-2 , 8.2-27 , 8.2-49 , 8.3-4
Switching frequency of inverter, 6.9-1
- noise optimised, 6.9-1
Switching frequency reduction, 6.9-2
System bus (CAN), wiring, 5.10-1
T
Table of attributes, 8.5-1
Technical data, 3-1
- current characteristic, device protection by current
derating, 3.4-1
- Operation with rated power, Rated data 480 V, 3.2-4
technical data, Operation with rated power, 3.2-1
Technicaldata
- Operation at rated power, Rated data 400 V, 3.2-1 , 3.3-1
- Operation with increased rated power, 3.3-1
Temperature detection, 8.2-59
Temperature ranges, 3.1-1
- Reduce rated current, 3.1-1
Terminal assignment
- analog inputs, 5.9-8
- analog outputs, 5.9-8
- digital inputs, 5.9-8
- digital inputs/outputs, 11.3-2
- digital outputs, 5.9-8
- Safety relay KSR, 5.9-8
- safety relay KSR, 11.3-2
Terminal data, 5.9-2 , 11.3-2
Terms
- controller, 13.1-1
- Definitions, 13.1-1
- drive, 13.1-1
Thermal monitoring, motor, with PTC thermistor, 6.6-8 ,
6.6-10
Tn current controller, 6.8-8 , 8.2-28 , 8.2-51 , 8.3-8
Tn slip controller, 6.11-1 , 8.2-29 , 8.3-8
Tn speed controller, 8.2-28 , 8.2-51 , 8.3-7
Torque control with speed limitation, in case of vector
control (MCTRL2), 8.2-63