What does 'Err 513 - System Error' mean on Lightmed LightLas 532?
If your Lightmed Medical Equipment displays 'Err 513 - System Error', it means the system stopped running. Contact an authorized service or the manufacturer for assistance.
What to do if Lightmed Medical Equipment shows 'Err 500 - ROM'?
If the Lightmed Medical Equipment displays 'Err 500 - ROM', it means the system didn't pass the software integrity test. Try rebooting the system. If the error persists, contact an authorized service or the manufacturer.
What does 'Err 501 - Shutter Failure' mean on Lightmed LightLas 532 Medical Equipment, and how to fix it?
If your Lightmed Medical Equipment shows 'Err 501 - Shutter Failure', this indicates that the shutter failed to open or close. Try rebooting the system. If the problem continues, contact an authorized service or the manufacturer.
What does Err 5041 mean for Lightmed LightLas 532?
If your Lightmed Medical Equipment displays 'Err 5041 - Laser Diode Temperature Out of Tolerance +/- 2.5C', it could be due to the ambient temperature being too high or low, preventing the laser temperature TEC from reaching a stable value within 5 minutes. Try rebooting the system. If the problem persists, contact an authorized service or the manufacturer.
How to fix 'Err 5051 - Remote Communication Error' on Lightmed Medical Equipment?
If your Lightmed Medical Equipment shows 'Err 5051 - Remote Communication Error', it means there's no communication between the remote and the laser console. Try rebooting the system. If the error continues, contact an authorized service or the manufacturer.
What does 'Err 5044 - Cavity Temperature Sensor Failure' mean on Lightmed LightLas 532?
If your Lightmed Medical Equipment displays 'Err 5044 - Cavity Temperature Sensor Failure', it indicates a failure of the cavity temperature sensor, or the sensor is open or shorted circuit. Contact an authorized service or the manufacturer for assistance.
What does 'Err 5043 - Cavity Temperature Out of Tolerance +/- 2.5C' mean on Lightmed LightLas 532?
If your Lightmed Medical Equipment displays 'Err 5043 - Cavity Temperature Out of Tolerance +/- 2.5C', it means the cavity temperature sensor cannot reach the preset value. Try rebooting the system. If the problem persists, contact an authorized service or the manufacturer.
What does 'Err 5042 - Laser Sensor Failure' mean on Lightmed Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 5042 - Laser Sensor Failure', it means the laser sensor has failed (opened or shorted sensor). Power off the equipment and contact an authorized service or the manufacturer for assistance.
What causes 'Err 506 - Delivery System Shutter Failure' on Lightmed Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 506 - Delivery System Shutter Failure', it means the slitlamp safety filter could not close. Check the safety filter moving operation. Alternatively, try rebooting the system or contact an authorized service or the manufacturer.
How to resolve 'Err5072- Communication Error' on Lightmed LightLas 532 Medical Equipment?
If your Lightmed Medical Equipment displays 'Err5072- Communication Error', it indicates there is no communication between the panel control and console CPU. Try rebooting the system. If the error persists, contact an authorized service or the manufacturer.
Essential safety guidelines and precautions for operating the LightLas 532 laser system.
Details potential optical hazards associated with laser operation and protective measures.
Provides crucial instructions on how to prevent exposure to direct or scattered laser radiation.
Outlines potential electrical hazards and necessary precautions to prevent shock.
Detailed explanation of the laser console's controls and the LCD panel interface.
Details the recommended procedures and prerequisites for installing the LightLas 532 laser system.
Steps for pre-checking and aligning the laser system components before operation.
Guidance on pre-checking and aligning the different Laser Delivery Units (LDUs).
Procedures for final testing and verification of the laser system's performance.
Pre-check and alignment procedures specific to the attachment slitlamp LDU.
Pre-check and alignment procedures for the Laser Indirect Ophthalmoscope (LIO).
Provides critical general warnings and safety precautions for using the laser system during treatments.
General| Laser Type | Diode Pumped Solid State (DPSS) |
|---|---|
| Wavelength | 532 nm |
| Cooling System | Air Cooled |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Pulse Duration | 10 ms to 3000 ms |
| Aiming Beam | Red Diode 635 nm |
| Operation Mode | Continuous |
| Applications | Retinal Photocoagulation |
| Delivery System | Slit lamp adapter, laser indirect ophthalmoscope (LIO) |
To Next Page
