What does 'Err 503 - Aiming Laser Failure' mean on Lightmed Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 503 - Aiming Laser Failure', it means there is an aiming laser beam failure or the laser intensity is greater than 1mW. Contact an authorized service or the manufacturer for assistance.
What does 'Err 502 - Laser Diode Current Too High' mean on Lightmed Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 502 - Laser Diode Current Too High', it means the laser diode current is out of range or over the limits. Contact an authorized service or the manufacturer for assistance.
What to do if there is no aiming beam on Lightmed LightLas 532 Medical Equipment (SD only)?
If your Lightmed Medical Equipment (SD only) has no aiming beam, it might be that the aiming beam intensity needs to be calibrated. Try rebooting the system. If the problem persists, it could be an aiming beam electric circuit failure, and you should contact an authorized service or the manufacturer.
How to troubleshoot no power or display on Lightmed LightLas 532?
If your Lightmed Medical Equipment shows no power or display, first, check the power source and connector. If that's not the issue, inspect the power fuses. Also, ensure the emergency button is in the outward ON position. If the problem continues, it's best to contact an authorized service or the manufacturer for help.
Why is there no or low output of the Green laser beam in Lightmed LightLas 532?
If you're experiencing no or low output of the green laser beam on your Lightmed Medical Equipment, first, check the fiber integrity by replacing it with a new one. Then, make sure the Treat mode is activated and the specified power is selected. If the issue persists, it may be due to a decayed laser cavity or electronics malfunction, in which case, contact an authorized service or the manufacturer.
What causes 'Err 506 - Delivery System Shutter Failure' on Lightmed Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 506 - Delivery System Shutter Failure', it means the slitlamp safety filter could not close. Check the safety filter moving operation. Alternatively, try rebooting the system or contact an authorized service or the manufacturer.
What does 'Err 510 - Watchdog Error' mean on Lightmed LightLas 532 Medical Equipment?
If your Lightmed Medical Equipment shows 'Err 510 - Watchdog Error', it means there is a system watchdog flag. Try to reboot the system. If the problem persists, contact an authorized service or the manufacturer.
How to resolve 'Err5072- Communication Error' on Lightmed LightLas 532 Medical Equipment?
If your Lightmed Medical Equipment displays 'Err5072- Communication Error', it indicates there is no communication between the panel control and console CPU. Try rebooting the system. If the error persists, contact an authorized service or the manufacturer.
What does 'Err 5071 - System Time Up Error' mean for Lightmed LightLas 532 Medical Equipment?
If your Lightmed Medical Equipment shows 'Err 5071 - System Time Up Error', it means the system stopped running. Try rebooting the system. If the error persists, contact an authorized service or the manufacturer.
What does 'Err 5054 - Remote Configuration Error' mean on Lightmed LightLas 532 Medical Equipment?
If your Lightmed Medical Equipment displays 'Err 5054 - Remote Configuration Error', it means the system can not configure laser console operation. Try rebooting the system. If the error persists, contact an authorized service or the manufacturer.
Essential safety guidelines and precautions for operating the LightLas 532 laser system.
Details potential optical hazards associated with laser operation and protective measures.
Provides crucial instructions on how to prevent exposure to direct or scattered laser radiation.
Outlines potential electrical hazards and necessary precautions to prevent shock.
Detailed explanation of the laser console's controls and the LCD panel interface.
Details the recommended procedures and prerequisites for installing the LightLas 532 laser system.
Steps for pre-checking and aligning the laser system components before operation.
Guidance on pre-checking and aligning the different Laser Delivery Units (LDUs).
Procedures for final testing and verification of the laser system's performance.
Pre-check and alignment procedures specific to the attachment slitlamp LDU.
Pre-check and alignment procedures for the Laser Indirect Ophthalmoscope (LIO).
Provides critical general warnings and safety precautions for using the laser system during treatments.
General| Laser Type | Diode Pumped Solid State (DPSS) |
|---|---|
| Wavelength | 532 nm |
| Cooling System | Air Cooled |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Pulse Duration | 10 ms to 3000 ms |
| Aiming Beam | Red Diode 635 nm |
| Operation Mode | Continuous |
| Applications | Retinal Photocoagulation |
| Delivery System | Slit lamp adapter, laser indirect ophthalmoscope (LIO) |
To Next Page
