Lightware MMX6x2-HT200 - Page 7

MMX6x2-HT
User’s Manual
Section 1. Introduction Page 7 / 119
8.5.13. Unmute an output ................................................................................................. 90
8.5.14. Lock an output ...................................................................................................... 91
8.5.15. Unlock an output ................................................................................................... 91
8.5.16. HDCP setting (input port) ..................................................................................... 91
8.5.17. HDCP setting (output port) ................................................................................... 91
8.5.18. Test pattern generator .......................................................................................... 92
8.5.19. TPS mode settings on TPS ports ......................................................................... 93
8.5.20. HDMI mode settings (output ports) ....................................................................... 93
8.6. AUDIO PORT SETTINGS ..................................................................................................... 94
8.6.1. Signal source selection .......................................................................................... 94
8.6.2. Analog audio input level settings ........................................................................... 94
8.6.3. Analog audio output level settings ......................................................................... 95
8.7. RS-232 PORT CONFIGURATION ......................................................................................... 96
8.7.1. Protocol setting ...................................................................................................... 96
8.7.2. BAUD rate setting .................................................................................................. 97
8.7.3. Databit setting ........................................................................................................ 97
8.7.4. Stopbits setting ...................................................................................................... 97
8.7.5. Parity setting .......................................................................................................... 97
8.7.6. RS232 operation mode .......................................................................................... 98
8.7.7. Send message via an RS-232 port ........................................................................ 98
8.8. NETWORK CONFIGURATION ............................................................................................... 99
8.8.1. Query the DHCP state ........................................................................................... 99
8.8.2. Change the DHCP state ........................................................................................ 99
8.8.3. Query the IP address ............................................................................................. 99
8.8.4. Change the IP address (static) .............................................................................. 99
8.8.5. Query the subnet mask .......................................................................................... 99
8.8.6. Change the subnet mask (static) ......................................................................... 100
8.8.7. Query the gateway address ................................................................................. 100
8.8.8. Change the gateway address (static) .................................................................. 100
8.8.9. Send message via a TCP port ............................................................................. 100
8.9. EDID MANAGEMENT ....................................................................................................... 101
8.9.1. Query the emulated EDIDs .................................................................................. 101
8.9.2. Query the validity of a dynamic EDID .................................................................. 101
8.9.3. Query a user EDID header .................................................................................. 101
8.9.4. Emulating an EDID to an input port ..................................................................... 102
8.9.5. Copy an EDID to user memory ............................................................................ 102
8.9.6. Deleting an EDID from user memory ................................................................... 102
8.9.7. Resetting the emulated EDIDs ............................................................................ 102
9. FIRMWARE UPGRADE .................................................................................................... 103
9.1. ABOUT THE FIRMWARE PACKAGE (LFP FILE) .................................................................... 103
9.2. SHORT INSTRUCTIONS .................................................................................................... 103
9.3. INSTALL AND UPGRADE ................................................................................................... 103
9.4. DETAILED INSTRUCTIONS ................................................................................................ 104
9.4.1. Establish the connection between the computer and the device(s) .................... 104
9.4.2. Start the LDU and follow the instructions ............................................................ 105
9.5. KEEPING THE CONFIGURATION SETTINGS AFTER FIRMWARE UPGRADE ............................... 109
9.6. REMOTE FIRMWARE UPGRADE OF CONNECTED LIGHTWARE DEVICES ................................ 110
10. APPENDIX......................................................................................................................... 111
10.1. SPECIFICATIONS ........................................................................................................ 111
10.2. MECHANICAL DRAWINGS ............................................................................................. 113
10.3. CONTENT OF THE BACKUP FILE ................................................................................... 114
10.4. INPUT AND OUTPUT PORT NUMBERING ......................................................................... 115
10.5. MAXIMUM TWISTED PAIR DISTANCES ............................................................................ 115
10.6. FACTORY DEFAULT SETTINGS ..................................................................................... 116
10.7. FACTORY EDID LIST .................................................................................................. 117
10.8. VERSION APPLICABILITY .............................................................................................. 118
10.9. LIMITED WARRANTY STATEMENT ................................................................................ 118
10.10. DOCUMENT REVISION HISTORY ................................................................................... 119