Lightware UMX-OPT-TX150R - Page 6

Page 6 / 107
6.7. AUDIO INPUT IN AUTOSELECT MODE .................................................................................................... 35
6.7.1. Static select .............................................................................................................................. 35
6.7.2. Non-priority (first detect) .......................................................................................................... 36
6.7.3. Priority detect – Embedded, S/PDIF, Analog audio 2.............................................................. 37
6.7.4. Priority detect – S/PDIF, Embedded, Analog audio 2 ............................................................. 38
6.7.5. Priority detect –Embedded, Analog audio 2 ............................................................................ 39
6.7.6. Priority detect – S/PDIF, Analog audio 2 ................................................................................. 39
6.7.7. Fix select – Embedded ............................................................................................................ 40
6.7.8. Fix select – Analog audio 1 ...................................................................................................... 40
6.7.9. Fix select – Analog audio 2 ...................................................................................................... 40
6.7.10. Fix select – S/PDIF .................................................................................................................. 40
6.8. ABOUT EDID MEMORY ....................................................................................................................... 41
6.8.1. EDIDs are referred with Lightware Matrix Controller ............................................................... 41
6.8.2. EDIDs are referred with rotary switches .................................................................................. 41
6.8.3. The assigning table .................................................................................................................. 42
6.8.4. Example state of the rotary switches ....................................................................................... 43
6.8.5. Switching the EDID with a rotary switch .................................................................................. 44
6.8.6. Deleting the EDID .................................................................................................................... 44
6.9. EDID TYPES ...................................................................................................................................... 44
6.9.1. Factory preset EDID list ........................................................................................................... 44
6.10. LEARNING THE EDID .......................................................................................................................... 45
6.11. SWITCHING THE EDID ........................................................................................................................ 46
6.12. DELETING THE EDID .......................................................................................................................... 46
6.13. HDCP MANAGEMENT ......................................................................................................................... 46
6.14. NO SYNC COLOR ................................................................................................................................ 47
6.15. HARDWARE RESET ............................................................................................................................. 47
6.16. RELOAD FACTORY DEFAULTS .............................................................................................................. 47
7. SERVICE MENU ..................................................................................................................................... 48
7.1. THE CONCEPT .................................................................................................................................... 48
7.1.1. The structure of the service menu ........................................................................................... 48
7.1.2. Service menu display ............................................................................................................... 48
7.1.3. Enter the service menu ............................................................................................................ 48
7.1.4. Navigation in the service menu................................................................................................ 49
7.1.5. Saving in the service menu ...................................................................................................... 49
7.1.6. Exit from service menu ............................................................................................................ 49
7.2. THE SERVICE MENU IN CASE OF UMX-OPT-TX150R ........................................................................... 51
7.2.1. The device specific structure of the service menu................................................................... 51
7.2.2. The device specific service menu display ............................................................................... 51
7.2.3. Enter the service menu of UMX-OPT-TX150R ........................................................................ 51
7.2.4. Navigation in the service menu of UMX-OPT-TX150R ........................................................... 52
7.2.5. Saving in the service menu in case of the UMX-OPT-TX150R ............................................... 52
7.2.6. Exit from service menu in case of the UMX-OPT-TX150R ..................................................... 52
8. REMOTE OPERATION .......................................................................................................................... 53
8.1. CONTROL INTERFACES ....................................................................................................................... 53
8.2. MULTIPLE SIMULTANEOUS CONNECTIONS ............................................................................................ 53
8.3. SERIAL PORT SETTINGS ...................................................................................................................... 53
9. SOFTWARE CONTROL – USING THE LIGHTWARE MATRIX CONTROLLER ................................. 54
9.1. INSTALLING THE MATRIX CONTROLLER SOFTWARE ............................................................................... 54
9.2. ESTABLISHING THE CONNECTION ......................................................................................................... 55
9.3. CONTROL MENU ................................................................................................................................. 57
9.3.1. Switch ...................................................................................................................................... 57
9.3.2. Toggle between the working modes ........................................................................................ 57
9.3.3. Input parameter settings .......................................................................................................... 58
9.3.4. Output parameter settings ....................................................................................................... 62
9.4. EDID MENU ....................................................................................................................................... 63
9.4.1. EDID Router operation ............................................................................................................ 63
9.4.2. Advanced EDID Editor ............................................................................................................. 65
9.4.3. Easy EDID Creator .................................................................................................................. 65