LiteOn EVO 6800 Series

Other manuals for LiteOn EVO 6800 Series

Questions and Answers:

N
Nathan GreerAug 23, 2025
What to do if my LiteOn DC Drives heatsink overheats?
- D
  Deanna Young DDSAug 23, 2025
  If your LiteOn DC Drives heatsink overheats, it could be due to: * High ambient temperature. * The internal cooling fan not operating. * Insufficient room for airflow. Here's what you can do: 1. Check the temperature around the drive: * Improve airflow inside the enclosure panel. * Install an air conditioner or fan to cool the environment. * Remove any heat sources. 2. Measure the output current: * Reduce the load. * Lower the setting in C6-00 (Carrier Frequency Option). 3. Replace the cooling fan.
U
usanchezSep 4, 2025
What to do if LiteOn DC Drives heatsink overheat?
- M
  Melissa GrantSep 4, 2025
  If your LiteOn DC drive's heatsink is overheating, first check the temperature around the drive. Improve airflow inside the enclosure, install a cooler, or remove heat sources. Also, measure the output current and reduce the load or lower the setting in C6-00 (Carrier Frequency Option). Finally, replace the cooling fan if needed.
J
Jennifer EllisSep 2, 2025
What causes Undertorque Detection 1 on LiteOn EVO 6800 DC Drives?
- B
  Brittany NelsonSep 3, 2025
  Undertorque Detection 1 on LiteOn DC Drives is triggered by: * Incorrect parameter settings. * Malfunction on the machinery side. To resolve this: 1. Reset P6-01 and P6-02. 2. Ensure there is no problem on the machinery side.
J
john52Sep 1, 2025
What causes Overtorque Detection 1 in LiteOn DC Drives?
- D
  Diane BeckerSep 1, 2025
  Overtorque Detection 1 in LiteOn DC Drives can be caused by: * Incorrect parameter settings. * Malfunction on machinery. To resolve this issue: 1. Reset P6-01 and P6-02. 2. Check machinery and load status.
C
Christina JonesAug 30, 2025
What does it mean if my LiteOn EVO 6800 DC Drives show PID Feedback Low?
- E
  Erin GrayAug 30, 2025
  If your LiteOn DC Drives shows a 'PID Feedback Low' error, it could be due to: * Inappropriate settings in b5-12 and b5-13. * Incorrect PID feedback wiring. * Feedback sensor malfunction. * Incorrect feedback input circuit. To fix this: 1. Correct b5-12 and b5-13 settings. 2. Correct the wiring. 3. Replace the sensor if it is damaged. 4. Contact the local distributor to replace the board or the drive.
N
natashatannerAug 29, 2025
What to do if LiteOn EVO 6800 show PID Feedback High?
- C
  carlos41Aug 29, 2025
  If your LiteOn DC Drives displays a 'PID Feedback High' error, the possible causes are: * Inappropriate settings in b5-22 and b5-23. * Incorrect PID feedback wiring. * Feedback sensor malfunction. * Feedback input circuit malfunction. To resolve this: 1. Confirm b5-22 and b5-23 settings. 2. Correct the wiring. 3. Replace the sensor if it is damaged. 4. Replace the PCB or drive. Contact the local distributor.
A
Ashley BrownAug 27, 2025
What causes Undervoltage in LiteOn DC Drives?
- D
  David GuerreroAug 27, 2025
  Undervoltage in LiteOn DC Drives can stem from: * Input power phase loss. * Loose wiring terminals of drive input power. * A problem with the voltage from the drive input power. * Weakened drive main circuit capacitors. * Damage to the contactor or relay on the soft-charge bypass circuit. To troubleshoot: 1. Correct the drive input power wiring. 2. Tighten the terminals. 3. Check the voltage: * Adjust the voltage according to the drive input power specifications. * Check the main circuit magnetic contactor if there is no problem with the power supply. 4&5. If problems persist after power cycling, consider replacing the drive or control board. Contact your local distributor for more assistance.
A
Amber WalkerAug 26, 2025
What causes External Fault ( Input Terminal S1 to S7 ) in LiteOn EVO 6800 and how to fix it?
- C
  Chad AllenAug 27, 2025
  An external fault in LiteOn DC Drives, indicated by Input Terminal S1 to S7, can be caused by: * An external device tripping an alarm. * Incorrect wiring. * Incorrect multi-function input wiring. To resolve this: 1. Remove the cause of the external fault, then reset the multi-function input. 2. Confirm the signal lines are properly connected to the terminals assigned for external fault detection (E1-??= 23 to 38). 3. Confirm if E1-??=23 to 38 is set to the unused terminals.
M
Matthew AnthonyAug 25, 2025
What to do if my LiteOn DC Drives motor overheats?
- S
  Steven HernandezAug 25, 2025
  If your LiteOn DC Drives motor is overheating, it could be due to: * Incorrect wiring for the motor temperature input (terminal MT). * A fault in the machinery (e.g., machinery is locked up). * Motor overheat. To address this: 1. Correct the wiring for terminal MT. 2. Check the machinery status. 3. Check the load, acceleration/deceleration time, and cycle time: * Reduce the load. * Increase the C1-00 to C1-07 (Acc./Dec. Time) settings. * Adjust d1-02 to d1-11 (V/F Characteristics).