EasyManua.ls Logo

MacroAir Technologies EnergyLogic AVD3 - User Manual

Default Icon
76 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 2019 EnergyLogic, LLC Toll Free: 800 311 8828 Fax: 615 471 5202 www.energylogic.com i
Rev. Date 040819
Installation
Manual
AVD3
5901 Crossings Blvd
Antioch, TN 37013
www.energylogic.com
(800) 311-8828

Table of Contents

Questions and Answers

MacroAir Technologies EnergyLogic AVD3 Specifications

General IconGeneral
ModelEnergyLogic AVD3
ManufacturerMacroAir Technologies
Power1.5 HP
Motor TypeDirect drive
Voltage120/240V
ApplicationCommercial, Industrial
Speed SettingsVariable Speed

Summary

Caution & Safety

Key Safety System Components

Details key safety features and installation requirements for fans.

Weight Considerations

Discusses structural support requirements and maximum hanging weight for fans.

Torque

Specifies the maximum torque handled by the mounting system.

Check Federal, State, and Local Codes

Advises checking relevant codes for compliance with regulations.

Windy Conditions

States fans should not be operated when wind is present.

Fusing Chart

Fan Placement & Clearance

Sprinkler Systems and Fan Placement

Guidelines for fan placement near fire sprinklers and code compliance.

Other Information on Placement and Spacing

Advice on fan placement relative to lights, mezzanines, and HVAC outlets.

Fan Dimensions

Network Wiring (Optional)

Components (Fixed Angle Mount)

Components (Universal Mount)

Fan Components and Tools

Tools Required

Lists the tools necessary for installation and maintenance of the fan.

Fixed Angle Mount

Mounting Bolt Kits

Details required bolt kits for I-Beam, Glulam, and Unistrut mounting.

I-Beam (Steel Truss Mounting)

Installation steps for mounting to I-beams or steel trusses over 3 inches wide.

Glulam

Installation steps for mounting to Glulams or wood beams.

Unistrut

Installation method for spanning components using Unistrut.

Extension Tube

Instructions for installing the extension tube for the fixed angle mount.

Motor Unit

Steps for attaching the motor unit to the mount and extension tube.

Safety Cable Installation

Procedures for installing the safety cable for fixed angle mounts.

Universal Mount

Mounting Bolt Kits

Details required bolt kits for I-Beam, Glulam, and Unistrut mounting.

I-Beam (Steel Truss Mounting)

Installation steps for mounting to I-beams or steel trusses over 3 inches wide.

Glulam

Installation steps for mounting to Glulams or wood beams.

Unistrut

Installation method for spanning components using Unistrut.

Extension Tube

Instructions for installing the extension tube for the universal mount.

Motor Unit

Steps for attaching the motor unit to the mount and extension tube.

Safety Cable Installation

Procedures for installing the safety cable for universal mounts.

Guy Wire Installation

Drive Installation

Drive Installation (Low Voltage)

Specific instructions for connecting low voltage single and three-phase power.

Drive Installation (High Voltage)

Specific instructions for connecting high voltage three-phase power.

Control Wiring

Details how to connect the CAT5e cable to the drive's terminal block or RJ45 port.

Airfoil Installation

Disconnect Switch

Fuse Disconnect Switch Installation

Steps for installing the optional fuse disconnect switch for safety.

Emergency Disconnect Schematic

Schematic for connecting fans to an emergency stop system.

Enable (ON);Disable (OFF) Schematic

Schematic for remote on/off fan control via supervisory contacts.

Touchpad Remote Mounting

Touchpad Remote Navigation

Touchpad Remote Operation

Maintenance Information

Mounting Plate Dimensions

Mounting Bracket Dimensions

Touchpad Remote Dimensions

Troubleshooting

Fault Code Causes and Possible Solutions

Lists fault codes, their causes, symptoms, and troubleshooting tips.

Warranty and Technical Support

Related product manuals