Mitsubishi Electric FX3U SERIES - Setup of Input;Output Connection Connector

B - 46
FX 3S /FX 3G /FX 3GC /FX 3U /FX 3UC PLC User's Manual - Positioning Control Edition
Built-in Positioning Functions
3 Connection of Input/Output Lines and Tightening Torques
3.3 Connector
3.3.2 Setup of Input/Output Connection Connector
1. Applicable connector (connector purchased at store)
Use a 20-pin (1-key) socket that conforms to the requirements of the MIL C-83503.
Preliminarily check that the peripheral parts, such as the connector cover, will not cause any interference.
2. Input/output cables (optional cables manufactured by our company)
Mitsubishi Electric can provide input/output cables already equipped with a connector.
3. Input/output cable connectors prepared by purchaser (optional connectors manufactured
by Mitsubishi Electric)
The purchaser should prepare the cables and press-fitting tools.
4. Connector already confirmed as applicable (available at stores)
Connectors manufactured by Daiichi Denshi Kogyo Co., Ltd. (shown in 3)
Model Length Description Connector type
FX-16E-500CAB-S
5m
(16’ 4")
General-purpose input/output cable
• Single wire (Wire color: red)
• PLC side: A 20-pin connector
FX-16E-150CAB
1.5m
(4’11")
Cable for connection of FX Series
terminal block to input/output connector
For details on connection to the FX
Series terminal block, refer to the
following manuals:
FX
3G Hardware Edition
FX
3GC Hardware Edition
FX
3U Hardware Edition
FX
3UC Hardware Edition
• Flat cables (with tube)
• A 20-pin connector at both ends
FX-16E-300CAB
3m
(9’10")
FX-16E-500CAB
5m
(16’ 4")
FX-16E-150CAB-R
1.5m
(4’11")
• Round multicore cables
• A 20-pin connector at both ends
FX-16E-300CAB-R
3m
(9’10")
FX-16E-500CAB-R
5m
(16’ 4")
FX-A32E-150CAB
1.5m
(4’11")
Cable for connection of A Series
A6TBXY36 connector/terminal board
conversion unit to input/output
connector type
• Flat cables (with tube)
• PLC side: Two 20-pin connectors in
16-point units
• Terminal block side: A dedicated
connector
• One common terminal covers 32 input/
output terminals
FX-A32E-300CAB
3m
(9’10")
FX-A32E-500CAB
5m
(16’ 4")
Input/output connector model and number
of connectors included in one set
Applicable cable
(recommended cable: UL-1061) and tool
Our model
Description of parts
(Manufactured by Daiichi
Denshi Kogyo Co., Ltd.)
Cable size
Crimping tool
(Manufactured by Daiichi
Denshi Kogyo Co., Ltd.)
FX
2C-I/O-CON, for flat
cable
Set of
10 parts
Crimp-style connector
FRC2-A020-30S
AWG28(0.1mm
2
)
1.27 pitch, 20 cores
357J-4674D main unit
357J-4664N attachment
FX
2C-I/O-CON-S, for
non-stranded cable
5 sets
Housing HU-200S2-001
Crimp-style contact HU-
411S
AWG22(0.3mm
2
)
357J-5538
FX
2C-I/O-CON-SA,
for non-stranded
cable
5 sets
Housing HU-200S2-001
Crimp-style contact HU-
411SA
AWG20(0.5mm
2
)
357J-13963
FX-I/O-CON2, for flat
cable (40 Pin)
2 sets
Crimp-style connector
FRC2-A040-30S
AWG28(0.1mm
2
)
1.27 pitch, 40 cores
357J-4674D main unit
357J-4664N attachment
FX-I/O-CON2-S
non-stranded cable
(40 Pin)
2 sets
Housing HU-400S2-001
Crimp-style contact HU-
411S
AWG22(0.3mm
2
)
357J-5538
FX-I/O-CON2-SA
non-stranded cable
(40 Pin)
2 sets
Housing HU-400S2-001
Crimp-style contact HU-
411SA
AWG20(0.5mm
2
)
357J-13963
Downloaded from ManualsNet.com search engine