natus Quantum User Manual

91 pages

To Next Page

Default Chapter3
- Table of Contents3
1 Getting Started7
- Quantum System Features7
- Intended Use8
- System Components8
- Essential Performance Degradation8
- Operating Principle of the Quantum Amplifier8
- Using the Manual10
  - Manual Conventions10
2 Safety & Standards Conformity11
- Standards of Compliance and Normative References11
- Declaration of Compliance for Iec 60601-1-213
- Declaration of Compliance for Fcc17
3 Contraindications and Warnings18
- Contraindications18
- Warnings and Cautions18
- Procedures and Warnings25
  - Electrostatic Discharge (Esd) Handling25
  - Conducted Immunity Procedures and Warnings25
4 Description of Symbols27
5 Specifications30
6 Product Images and Description33
- Quantum Amplifier System with 128 to 256 Channels33
- Quantum 64 Amplifier System34
- Natus Base Unit35
- Quantum Breakout Boxes Main Andb36
  - Quantum Breakout Main, Bottom View37
- Quantum Pin Box Options37
- Quantum 64 Breakout Box40
- Quantum 64 Pin Box Options41
  - Standard Numerical Pin Boxes41
  - Bulk Connector Pin Box41
7 Setup42
- Connecting the Natus Base Unit42
- Potential Equalization Conductor42
- Connecting the Breakout Boxes to the Natus Base Unit42
  - Connecting to the Secondary Breakout Box43
  - Removing the Connections43
- Connecting the Standard or Bulk Connector Pin Boxes to the Breakout Box44
- Quantum 10-10/10-20 Pin Box44
- Quantum Amplifier System Connection Diagram47
- Quantum 64 Amplifier System Connection Diagram48
8 Configuring the Natus Base Unit49
- Setting the Ip Address49
- Touchscreen Icons52
9 Amplifier Usage and Features54
- Getting Started54
- Placement of the Operator and Patient54
- Creating Acquisition Profiles for Studies with Quantum or Quantum 64 Breakouts54
- Beginning a Study55
- Recording in Ambulatory Mode57
- Connecting the Nicolet Cortical Stimulator60
- Powering down the System61
- Adding the Quantum or Quantum 64 Breakout Box(Es) to the Modular Pouch62
- Quantum Amplifier System Communication Mode64
- Breakout Box Led Indicators65
  - Breakout Main Indicators Are Shown below65
  - Breakout Bindicators Are Shown below65
10 Animal Research66
- Independent References Mode Versus Common Reference Mode66
- Connecting Multiple Subjects to the Quantum or Quantum 6466
  - Setting up Neuroworks for Multiple Subject Connections67
11 Transport System Specifications and Maintenance69
- Xltek Trolley Specifications69
- Neurowand Cart (Nopc) Specifications70
- Roll Stand Specifications71
- Natus Ergojust Cart Specifications71
- Maintenance72
- Warnings and Cautions72
12 Electrical Input and Isolation Transformer Details73
13 Pulse Oximeter74
- Pulse Oximeter Specifications74
- Pulse Oximeter Instruction for Use74
- Pulse Oximeter Accessories74
  - Available Nonin Oximetry Sensors75
- Pulse Oximeter Precautions and Warnings75
14 Maintenance, Cleaning, & Disposal76
- Quantum Amplifier Pouch76
- Recommendations76
- Disposal77
15 Troubleshooting78
- Problems with Signal Quality79
16 Accessories & Replacement Parts List80
17 Getting Help83
18 Appendix A84
- Digital Trigger Input Port Wiring Diagram84
Appendix A84
19 Appendix B86
- Bulk Connector Pin Box Input86
- Bulk Connector Pin Box Input Wiring Diagram86
Appendix B86
20 Index88

Questions and Answers:

D
dean75Aug 3, 2025
What to do if acquired waveforms are flat on natus Quantum Medical Equipment?
- F
  floreskennethAug 3, 2025
  If the acquired waveforms on your Natus Medical Equipment are flat, do not appear, or do not appear correctly, try these steps: First, shut down the computer for at least 10 seconds, and then set up the test again from the beginning. Ensure there's a tight connection between the headbox, the breakout box, and the computer. Also, verify that the patient electrodes are connected to the correct channel in the headbox and fit properly (not loosely). Inspect your cables and change the acquisition cable. Check the gain and timebase settings to ensure that they are appropriate for the current test.
A
aguilarmichaelAug 17, 2025
Why are waveforms flat on natus Quantum?
- M
  Melissa ThomasAug 17, 2025
  If you're experiencing issues with flat or incorrect waveforms on your Natus Medical Equipment, consider the following: Ask the patient to relax. Unplug any other devices on the same circuit, such as printers or mechanical beds, that could cause interference. If electrodes are touching, separate them to prevent short circuits and artifacts. Finally, ensure your clinic has a properly grounded electrical system by installing a medical grade ground.

natus Quantum Specifications

General

Impedance Check	Yes
Video Integration	Yes
Input Impedance	> 100 MΩ
Power Supply	100-240 VAC, 50/60 Hz
Channels	256
Connectivity	Ethernet
Type	EEG Amplifier
Resolution	24-bit
Interface	Ethernet