45
PROGRAMMING
PROCEDURES
ACCESSING PROGRAMMING MODES
To access the various programming modes, press the PROG key. The following
messages will be displayed for each press of the PROG key. When the desired mode
is displayed, press the ENTER key to enter that mode. To quickly get to a
programming mode, press the PROG key and then press the number of the screen. If
you have pressed the PROG key by mistake, or want to exit out without having to
press the PROG key several times, press EXPN.
Refer to the following sections for the individual programming instructions. To escape
from any programming session press the PROG key.
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
PROGRAM ON MAINPROGRAM ON MAIN
PROGRAM ON MAINPROGRAM ON MAIN
PROGRAM ON MAIN
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
ASSIGN LOCO->CABASSIGN LOCO->CAB
ASSIGN LOCO->CABASSIGN LOCO->CAB
ASSIGN LOCO->CAB
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
SET SYSTEM CLOCKSET SYSTEM CLOCK
SET SYSTEM CLOCKSET SYSTEM CLOCK
SET SYSTEM CLOCK
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
USE PROGRAM TRKUSE PROGRAM TRK
USE PROGRAM TRKUSE PROGRAM TRK
USE PROGRAM TRK
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
SET CMD STATIONSET CMD STATION
SET CMD STATIONSET CMD STATION
SET CMD STATION
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
SET CAB PARAMSSET CAB PARAMS
SET CAB PARAMSSET CAB PARAMS
SET CAB PARAMS
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
PROG ACCESSORIESPROG ACCESSORIES
PROG ACCESSORIESPROG ACCESSORIES
PROG ACCESSORIES
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
PROGAM MACROSPROGAM MACROS
PROGAM MACROSPROGAM MACROS
PROGAM MACROS
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
BROWSE CONSISTSBROWSE CONSISTS
BROWSE CONSISTSBROWSE CONSISTS
BROWSE CONSISTS
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PMSEL MODE 02:00PM
SEL MODE 02:00PM
PROGRAM SIGNALSPROGRAM SIGNALS
PROGRAM SIGNALSPROGRAM SIGNALS
PROGRAM SIGNALS
To program locomotive decoders on the main
(OPS mode) press ENTER.
To assign a locomotive/consist to a Cab
press ENTER. [2]
To start, stop, or set the System Clock
press ENTER [3]
To program on the program track press
ENTER. [4]
To set command station parameters press
ENTER. [5]
To set the Cab parameters press ENTER. [6]
To program accessory decoders on the main
press ENTER. [7]
To setup macros (routing through turnouts)
press ENTER. [8]
To browse through all the advanced consists
in the system, press ENTER [9] To
program accessory decoders on the main
press ENTER. [10]
To Next Page
Loading...
