NETGEAR WAC510 User Manual

(Continued)
CommentsPublish DatePublication
Part Number
We added or made major changes to the following sections:
Set up an open or secure WiFi network on page 45
Enable or disable PMF for a WiFi network on page 59
Manage local MAC access control lists on page 110, including Manually set up a
MAC access control List on page 110 and Import an existing MAC access control
list on page 114
Change the management mode to NETGEAR Insight or Web-browser on page
160
Manually download firmware and upgrade the access point on page 171
Revert to the backup firmware on page 173
Perform a ping test on page 214
Technical specifications on page 231
For all sections to which it applies, we added a step that describes the action that
is required in the pop-up warning window.
December
2017
202-11840-02
We added or made major changes to the following sections:
Connect over WiFi using a WiFi-enabled computer or mobile device on page 29
Connect over Ethernet using a computer connected to the same network on
page 33
Connect over Ethernet using a directly connected computer on page 37
Set up an open or secure WiFi network on page 45
Register and configure Facebook Wi-Fi for the access point on page 71
Set up a click-through captive portal for a WiFi network on page 65
Unregister the access point from Facebook Wi-Fi on page 75
Manage the advanced WiFi settings for the radios on page 91
Manage neighbor AP detection on page 120
Set up RADIUS servers on page 126
Disable the DHCP client and configure a LAN or WAN IP address on page 129
September
2017
202-11840-01
(202-11840-01, September 2017, Continued)
Enable the DHCP client on page 135
Set the 802.1Q VLAN and management VLAN on page 138
Enable or disable IGMP snooping on page 145
Router mode only: Manage DHCP servers on page 148, including Manage the
default DHCP server on page 149 and Enable or disable inter-VLAN routing on
page 157
Change the management mode to NETGEAR Insight or Web-browser on page
160
Manage the LEDs on page 186
View unknown and known neighbor access points on page 195
View client distribution, connected clients, and client trends on page 197
View WiFi and WAN traffic, traffic statistics, and channel utilization on page 201
View a WiFi bridge connection on page 207
Capture WiFi and Ethernet packets on page 212
In addition, we made minor changes to other sections and updated some figures.
September
2017
202-11840-01
5
Insight Managed Smart Cloud Wireless Access Point WAC510 User Manual

NETGEAR WAC510 Specifications

General

2.4 GHz	Yes
Frequency band	2.4 - 5 GHz
Networking standards	IEEE 802.11ac, IEEE 802.11i, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1200 Mbit/s
Maximum data transfer rate (5 GHz)	867 Mbit/s
Maximum data transfer rate (2.4 GHz)	400 Mbit/s
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	2
Internal	No
Placement	Ceiling, Wall
Product color	White
LED indicators	Link, Network, Power
Antenna gain level (max)	6 dBi
Security algorithms	WPA, WPA2
Service Set Identifier (SSID) features	SSID broadcast on/off
Input current	2.5 A
AC input voltage	12 V
Power consumption (typical)	9.3 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	10 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Width	197.32 mm
Height	37 mm
Weight	555.5 g