Omron CP1E CPU UNIT SOFTWARE - Index

Index-1
CP1E CPU Unit Software User’s Manual(W480)
Index
Symbols
*D(Specifying indirect addresses
in BCD Mode)..................................................4-13, 5-12
@D(Specifying indirect addresses
in Binary Mode)...............................................4-13, 5-12
Numerics
1:N NT Links .......................................................14-3, 14-5
A
Absolute coordinates .................................................12-11
Absolute positioning...................................................12-11
ACC instruction .................................................12-9, 12-15
Access Error Flag(P_AER) ..........................................5-19
Allocated words
CPU Unit ..................................................................6-3
Expansion I/O Unit ...................................................6-4
Allocating functions to built-in input terminals ................8-6
Allocating functions to built-in output terminals..............8-8
Allocations for Expansion I/O Units................................6-4
Allocations for Expansion Units .....................................6-6
Always OFF Flag(P_Off)..............................................5-19
Always ON Flag(P_On)................................................5-19
Automatic I/O comment creation................................18-13
Automatic symbol name creation...............................18-13
Auxiliary Area........................................................5-4, 5-17
B
Backing up memory .......................................................3-5
Backup .........................................................................5-12
Backup area .............................................................3-5
I/O memory backup time ..........................................3-7
Backup memory ....................................................3-6, 16-8
Backup time ...................................................................1-2
Bit addresses .................................................................5-5
Built-in EEPROM .......................... 2-2, 2-3, 3-6, 5-12, 16-8
Built-in RAM ............................................................2-2, 2-3
Built-in RS-232C Port.....................................................7-5
C
C Mode command.............................................14-4, 14-30
Carry Flag(P_CY) ........................................................5-19
CIO Area.................................................................5-2, 5-7
Allocation..................................................................6-2
Circular (Ring) mode(high-speed counter).................11-11
Clock function ..............................................................16-7
Clock Pulses .........................................................5-4, 5-21
Communications settings........................................7-5, 7-8
Condition Flags.....................................................5-4, 5-19
Connecting the Servo Drive and external sensors.......12-5
Constants.....................................................................4-16
Counter Area..................................................................5-4
Resetting or maintaining ........................................5-16
Types ......................................................................5-15
Counter Completion Flags .............................................5-4
Counter PVs...................................................................5-4
Counting ranges.........................................................11-10
CPU Unit
I/O allocation ............................................................6-3
Internal memory .......................................................2-2
Memory areas and stored data ................................2-3
Operating modes......................................................3-3
Operation..................................................................3-2
CTBL instruction ........................................................11-21
CX-Programmer
Help........................................................................18-6
Cycle time ......................................................................3-2
I/O response time.................................................. A-80
Interrupt response time ......................................... A-82
Cycle time response performance .............................. A-80
Cyclic refreshing ..........................................................4-15
D
Data formats ................................................................4-13
Data Memory Area................................................5-3, 5-11
Data refresh method ..................................................14-23
Defining origin position...............................................12-18
Operating mode....................................................12-23
Operation pattern .................................................12-28
Origin return .........................................................12-30
Origin search operation setting ............................12-27
PLC Setup............................................................12-19
Differential phase input (4×).........................................11-8
DM Area capacity...........................................................1-2
DM backup function .....................................................16-8
E
End code(No-protocol communications)......................14-8
Equals Flag(P_EQ)......................................................5-19
Error Flag(P_ER) .........................................................5-19
E-type CPU Unit.............................................................1-2
Execute process settings ...............................................7-3
F
FINS command.................................................14-4, 14-30
Forced set/reset .........................................................18-25
Functions allocation
Selecting functions in the PLC Setup.......................8-4
Specifying method....................................................8-4
G
Global symbols ..............................................................4-6
Greater Than Flag(P_GT)............................................5-19
Greater Than or Equals Flag(P_GE) ...........................5-20
H
High-speed counter interrupts...........................11-2, 11-14
Application example .............................................11-27
Functions allocation................................................11-4
PLC Setup...................................................11-3, 11-16
Related Auxiliary Area..........................................11-26
Specifications .........................................................11-7
Writing the ladder program..........................11-6, 11-16
High-speed counter settings ........................................7-11
High-speed counters
Counting ranges...................................................11-10
Frequency measurement......................................11-13
Pulse input methods...............................................11-8
Reading the present value ...................................11-12
Reset method.......................................................11-11