Omron SYSMAC CS Series - User Manual

316 pages

Save Page as PDF

To Next Page

OPERATION M ANUAL

Cat. No. W406-E1-09

SYSMAC CS/CJ Series

Loop Control Boards

CS1W-LCB01/LCB05

Process-control CPU Units

CS1D-CPU@@P

(CPU Unit: CS1D-CPU@@H, Loop Controller: LCB05D)

Loop-control CPU Units

CJ1G-CPU42P

(CPU Unit: CJ1G-CPU42H, Loop Controller: LCB01)

CJ1G-CPU43P/44P/45P

(CPU Unit: CJ1G-CPU43H/44H/45H, Loop Controller: LCB03)

Main Page

Questions and Answers

M
Mary RobertsonSep 9, 2025
Why Omron Controller failed to open the Command log file?
- D
  Debra KingSep 10, 2025
  If the Omron Controller fails to open the Command log file and the operation exits, the file might not exist or has a wrong format. Specify a Command log file of a correct format.
M
mendozawilliamSep 8, 2025
What causes Omron SYSMAC CS to fail to open the CSV text file?
- N
  Nicole WrightSep 8, 2025
  If the Omron Controller fails to open the CSV text file and the operation exits, the file either does not exist or has a wrong format. Specify a Data Replay file (CSV text file) of a correct format, which is different from an execution file of the I/O Condition Tool.
A
awarrenSep 7, 2025
Why Omron Controller failed to read the routing table for FinsGateway?
- A
  Aaron RobertsSep 7, 2025
  If the Omron Controller fails to read the routing table for FinsGateway, it indicates a wrong setting of the routing table. Reset the routing table using the CX-Net to correct this.
A
Allison LuceroAug 22, 2025
How to fix Omron SYSMAC CS communications error with CX-Simulator Ladder Engine?
- A
  amy67Aug 23, 2025
  If a communications error occurs with the Omron Controller CX-Simulator Ladder Engine, it might be due to a wrong communications environment. Try the following: 1. Disconnect and then connect again. 2. Exit any running application programs except for the CX-Simulator. 3. Uninstall and then reinstall the CX-Simulator.
M
masonandrewSep 4, 2025
How to fix Omron SYSMAC CS Controller failed to create command log file?
- J
  Julie NguyenSep 5, 2025
  If the Omron Controller fails to create a command log file, it may be because the specified file is read-only or the disk space is low. Increase the disk space or change the destination for creating the log file.
S
samantha42Sep 3, 2025
Why Omron SYSMAC CS failed to create a PLC data folder?
- J
  Jasmine LeeSep 4, 2025
  If the Omron Controller fails to create a PLC data folder, it might be due to low hard disk space or insufficient access rights. Check if the folder is read-only or if the user has the necessary write permissions.
C
cantrelllindseySep 2, 2025
What causes Omron SYSMAC CS to fail to read the PLC data file?
- Z
  zrodriguezSep 2, 2025
  If the Omron Controller fails to read the PLC data file, it could be because the set file is broken. Reset the set file in the setting wizard to resolve this.
A
adam65Sep 1, 2025
What to do if Omron SYSMAC CS Controller failed to start FinsGateway?
- D
  Dominic WattsSep 1, 2025
  If Omron Controller's FinsGateway fails to start, it might be due to incorrect installation or invalid settings. Re-install the CX-Programmer, CX-Server, or FinsGateway to resolve this issue.
I
ithompsonAug 31, 2025
Why Omron Controller failed to start Data Replay Tool?
- R
  Rachael MartinAug 31, 2025
  If the Omron Controller Data Replay Tool fails to start, it may be due to a wrong execution environment. To resolve this, follow these steps: 1. Exit any running application programs except the CX-Simulator and try again. 2. Uninstall and then reinstall the CX-Simulator.
M
michael95Aug 30, 2025
How to fix Omron SYSMAC CS Controller failed to start Log display application?
- L
  Linda PopeAug 30, 2025
  If the Omron Controller Log display application fails to start, it may be due to a wrong execution environment. Try the following: 1. Exit any running application programs except for the CX-Simulator and try again. 2. Uninstall and then reinstall the CX-Simulator.